查看所有试题
- 孔径千分尺的测微螺距是0.25mm,测微螺杆旋转一周,则三爪组成的园周半径位移是()。在检定大量块时,为了使其变形最小,采用两支点支承,其支承点应选择()。0.25mm#
0.5mm
0.75mm贝塞尔点
艾利点#
距量块端面0.2232L
- 分度值为0.05mm/m的条式水平仪,零位误差不超过()。分度值的1/4#
分度值的1/3
分度值的1/2
- 角度规对零位时,游标零刻线应与主尺零刻线应重合。游标的尾刻线与主尺相应刻线重合,其不重合度不大于()。杠杆表指针末端及表盘刻线宽度为()深度百分表的示值误差不应大于()。1个分度值#
1/2个分度值
1/3个分度
- 在检定量杆时,为使杆的长度变化最小,通常采用贝塞尔点进行支承。已知杆长为L,两支承点距杆两端面距离均为a,则满足贝塞尔点的条件是()。非接触测量是测量装置的()元件与被测工件表面不直接接触,因而没有机械作用
- 千分尺校对用的量杆,其两端平工作面的平行度符合要求,而长度尺寸超过了要求时,可按实际尺寸使用,其实际尺寸是()。一面上各点中的一点至另一面的最大垂直距离(即最大尺寸)
一面上各点中的一点至别一面的最小垂直
- 检定游标量具游标刻线面的棱边至主尺刻线面的距离是为了控制()。视差#
读数误差
刻度误差
- 用等厚干涉法检定平品平面度时,在整个视场中干涉条纹的条数以调整到如下情况为最宜()。干涉条纹尽量少
2条或4条
3条或5条#
- 齿厚游标卡尺的齿高量爪测量面与齿厚量爪端面的平行度应不超过()。0.006mm
0.01mm#
0.015mm
- 计量器具新产品定型鉴定由()进行。在我国法定计量单位中,重量是质量的俗称,它的符号是()。国务院计量行政部门授权的技术机构#
省级法定计量检定机构
县级法定计量检定机构kg#
kgf
kG
- 比较仪指针末端应盖住分度盘短刻线长度的()。20-70%
30-80%#
40-90%
- 标准件的精度要求较高,一般应比被测件的精度高二级左右,同时还应有较高的()。下面是计量不确定度的几种定义,国际通用的定义是()。内径千分表的示值误差受检点是每隔()检一点。尺寸准确性
耐磨性
尺寸稳定性#表
- 内测千分尺的示值误差,对于测量范围至50mm的不超过()。±8μm#
±4μm
±6μm
- 测量基面的选择要遵守基面统一原则,即设计、工艺、测量和装配等基面一致,并尽可能的以()为基准。设计基面#
工艺基面
装配基面
- 长度相同的铜棒和铝棒,已知铝材料的线膨胀系数比铜大,则在相同测量条件下,测出的结果是()。铜棒比铝棒长
铜棒比铝棒短#
一样长
- 1、2、3级量块,可分别代替()等量块使用。1;2;3
3;4;5
4;5;6#
- 指示表(百分表、千分表)测杆受径向力对示值影响的检定所用的检定器具是()。结果满足阿贝原则的量具,所产生的误差是()。经向力工具
尺寸为10mm五等量块
半径为10mm半园柱侧块#一次误差
二次误差#
三次误差
- 检定高度和深度游标卡尺的示值误差时,所用的平板应是()。0级
1级#
2级
- 指示表(百分表、千分表)大指针的末端应盖住表盘短刻线长()。某运动员在100米赛跑中取得的成绩,用法定计量单位符号正确的表示是()。20-80%
30-70%
30-80%#958
9"8
9.8S#
- 深度百分表的示值变动性不应大于()。3μm
4μm
5μm#
- 在检定大量块时,为了使其变形最小,采用两支点支承,其支承点应选择()。已知某仪器最大允许误差为3(置信概率0.9973),则其B类不确定度表征值为()。贝塞尔点
艾利点#
距量块端面0.2232L点1#
2
3
4
- 杠杆齿轮式比较仪的示值变化及示值误差在非正常方位时,可按正常方位放大()。20%
30%
50%#
- 在接触测量中,其接触形式对测量结果也有影响,最常见的接触形式有点接触、线接触和面接触。从误差角度考虑,点接触所引起的误差为()。非接触测量是测量装置的()元件与被测工件表面不直接接触,因而没有机械作用的测
- 量块测量面的粗糙度直接影响量块的()大小。接触面
平面度
研合力#
- 无论尺框紧固与否,齿厚卡尺的综合误差应不超过()。分度值为0.05mm/m的条式水平仪,零位误差不超过()。±0.01mm
±0.02mm
±0.03mm#分度值的1/4#
分度值的1/3
分度值的1/2
- 若用平晶检测被测件,测量面上的干涉条纹为园形时,其测量面的凹凸情况可以这样进行判定:在平晶中央加压,若干涉条纹向内跑,则说明测量面中间是()。游标卡尺刀口内量爪的尺寸和平行度用1级外径千分尺检定,其所用千分
- 扭簧表在自由状态下,指针应位于负刻度的()。在我国法定计量单位中,重量是质量的俗称,它的符号是()。内侧
外侧#
正中kg#
kgf
kG
- 在测量量块的平面平行性时,除了采用()技术外,一般都是从中心长度与四个角点的长度相比较,取其中最大绝对值作为该量块平面平行性偏差。内径量表示值误差是在工作行程()上进行检定。光栅
激光
光波干涉#正向(测头
- 1、2、3级量块,可分别代替()等量块使用。形位公差的公差带限制实际开关或实际位置的()。1;2;3
3;4;5
4;5;6#变动量
公差
变动区域#
- 标准件的精度要求较高,一般应比被测件的精度高二级左右,同时还应有较高的()。测量基面的选择要遵守基面统一原则,即设计、工艺、测量和装配等基面一致,并尽可能的以()为基准。尺寸准确性
耐磨性
尺寸稳定性#设计
- 扭簧表指针的指向与刻线方向一致,应无目力可见()断线
偏斜#
翘起
- 千分尺校对用的量杆,其两端平工作面的平行度符合要求,而长度尺寸超过了要求时,可按实际尺寸使用,其实际尺寸是()。一面上各点中的一点至另一面的最大垂直距离(即最大尺寸)
一面上各点中的一点至别一面的最小垂直
- 游标卡尺刀口内量爪的尺寸和平行度用1级外径千分尺检定,其所用千分尺的测力应为()。用研磨面平尺检定样板直尺工作棱边的直线度时,所产生的间隙长度不应超过被检样板直尺工作棱边长度的()。6-12N
4-7N
6-7N#1/3#
- 用平行平晶来检定杠杆式卡规,两测量面的平行度,检定所需平晶数的()。量块的等是在检定时,根据中心长度的测量极限误差,平行面平行度偏差的及其他检定要求,即()确定。一块#
二块
三块测量精度
制造精度
检定误差#
- 分度值为0.02mm的游标卡尺,其刻线宽度及宽度差是()。(0.10-0.20)mm和0.05mm
(0.08-0.12)mm和0.02mm#
(0.08-0.15)mm和0.03mm
- 在使用平晶时,如果用手触摸平晶时间过长,会使平晶平面度()。变凹#
变凸
不变
- 在检定量杆时,为使杆的长度变化最小,通常采用贝塞尔点进行支承。已知杆长为L,两支承点距杆两端面距离均为a,则满足贝塞尔点的条件是()。孔径千分尺的测微螺距是0.25mm,测微螺杆旋转一周,则三爪组成的园周半径位移
- 非接触测量是测量装置的()元件与被测工件表面不直接接触,因而没有机械作用的测量力。敏感#
灵敏
灵活
- 用平晶以光波干涉法检定量具工作面的平面度时,出现干涉条纹或干涉环,其干涉原理是()。球面干涉
等倾干涉
等厚干涉#
- 比较仪工作台面与测量轴线的垂直度应不大于()。检定游标高度尺的示值误差或量爪工作面与基座工作面的平行度时,在1级平板上进行,对1级平板来说,其平面度不大于()。在使用平晶时,如果用手触摸平晶时间过长,会使平
- 内径千分表的示值误差受检点是每隔()检一点。0.1mm
0.02mm
0.05mm#