查看所有试题
- 当流量仪表用于测量瞬态快速变化的流量时,需要了解其()。下列三种说法,哪一种是正确的?()高温高压机组的高压加热器属于()压力容器。A、动态特性#
B、静态特性
C、流体特性
D、流动特性热处理应在焊接工作全部
- 有一台压力容器,在P=0.6MPa,T=430℃条件下稳定运行,材质为16MnR,经长期使用后筒体接管处发生塑性变形,其原因可能是()。除氧器壳体上的焊缝宜位于支座之外,焊缝离开支座垫板边缘的距离不应小于()mm。压力容器检测
- 20R钢板用作非低温压力容器壳体,厚度38mm,应符合()要求。当使用温度低于0℃时,应每批取2张钢板进行夏比(V型缺口)低温冲击试验。#
逐渐进行超声波探伤
在正火状态下使用
- 第三类压力容器的A、B类焊缝,必须进行()射线或超声波检测。全部#
50%
20%
- 依据《固定式压力容器安全技术监察规程》,判断下列有关压力容器焊接接头返修的说法哪些是正确的?()《固定式压力容器安全技术监察规程》规定受压元件的焊补,同一部位不宜多次补焊,一般不宜超过()。应分析缺陷产
- Q235-A用于压力容器壳体的厚度限制是()。《压力容器定期检验规则》中规定:碳素钢和16MnR钢制压力容器在液压试验时,液体温度不得低于(a)。其他低合金钢制压力容器,液体温度不得低于()。≤16mm#
≤20mm
≤30mm5℃
1
- 在其它条件相同时,外压容器开孔补强所需补强面积是内压容器开孔补强所需补强面积的()。低压容器的压力为()Mpa。《压力容器定期检验规则》中规定:现场检验工作结束后,一般设备应当在10个工作日内,大型设备可以在
- 《压力容器定期检验规则》中规定:碳素钢和16MnR钢制压力容器在液压试验时,液体温度不得低于(a)。其他低合金钢制压力容器,液体温度不得低于()。5℃
10℃
15℃#
- 下述项目中,哪些是压力容器设计总图中一般应注明的内容?()安全状况等级为()级的固定式压力容器,一般不得继续使用。最大工作压力#
最大允许工作压力
容积#
计算厚度3
4#
5
- 下述项目中,哪些是压力容器设计总图中一般应注明的内容?()最大工作压力#
最大允许工作压力
容积#
计算厚度
- 在对压力容器受压元件进行应力校核计算时,所用的厚度值为该元件的()。《电站压力式除氧器技术规定》中规定:除氧器的结构型式单机容量在200MW及以上汽轮机组的除氧器应采用()结构。大气式除氧器属于()。计算厚
- 各类压力容器的安全阀每年至少进行()放气试验。1次#
2次
4次
- 有一台压力容器,在P=0.6MPa,T=430℃条件下稳定运行,材质为16MnR,经长期使用后筒体接管处发生塑性变形,其原因可能是()。下述项目中,哪些是压力容器设计总图中一般应注明的内容?()安全状况等级为()级的固定式压
- 在对压力容器受压元件进行应力校核计算时,所用的厚度值为该元件的()。《压力容器定期检验规则》规定:压力容器一般应在投用满()时进行首次全面检验。计算厚度
设计厚度
有效厚度#
最小厚度一年
一个小修周期
三
- 下列哪些指标不是《固定式压力容器安全技术监察规程》列出的压力容器设计总图上主要特性参数的内容?()《压力容器定期检验规则》中规定:检查中发现压力容器用材不明时,但经过检验未查出新生缺陷(不包括正常的均
- 下列三种说法,哪一种是正确的?()高压加热器容器为()容器。热处理应在焊接工作全部结束并经验收合格后,于压力试验之后进行
热处理应在焊接工作全部结束并经验收合格后,于压力试验之前进行#
压力试验应在焊接工作
- 在其它条件相同时,外压容器开孔补强所需补强面积是内压容器开孔补强所需补强面积的()。依据《固定式压力容器安全技术监察规程》,判断下列有关压力容器焊接接头返修的说法哪些是正确的?()《压力容器定期检验规则
- 在对压力容器受压元件进行应力校核计算时,所用的厚度值为该元件的()。下述项目中,哪些是压力容器设计总图中一般应注明的内容?()低压容器的压力为()Mpa。下列哪些指标不是《固定式压力容器安全技术监察规程》
- 下列哪些指标不是《固定式压力容器安全技术监察规程》列出的压力容器设计总图上主要特性参数的内容?()电力锅炉压力容器安装前必须由()进行安全性能检验。储氢罐属于()容器。压力容器容积
压力#
换热器换热面