查看所有试题
- 在上塔提馏段氩富集区气相氩含量比液相氩含量()。如果进塔空气量以及氧产量不变,污氮产量增加,则氧气纯度将()。只要不出现液体,膨胀机后气体过热度()越好。筛板塔塔板阻力主要由:()组成。(1)干塔板阻力(
- 如果进塔空气量不变,氧气产量提高,则氮纯度将()。气体在压缩机内,排气压力降低,排气温度将()。降低
提高#
不变
无法确定降低#
升高
不变
无法确定
- 气体流速越大,吸附剂吸的附效果()。上塔压力降低,下列说法不正确的是:()。不变
越好
越差#
无法确定可改善上、下塔的精馏工况
可增加氧产量。
单位制氧能耗将升高#
有利于氧氮的分离
- 热力学温标的基准点是()。0K
1标准大气压下纯水的冰点
1标准大气压下纯水的沸点
水的三相点#
- 板式换热器热端温差越大,则复热不足冷损()。在精馏塔内,随着压力的降低,气相与液相之间的浓度差将()。适当提高()可以提高压缩机的效率。(1)机前温度,(3)机后压力。越多#
越少
不变
无法确定减少
增加#
不
- 气体在压缩机内,压缩比降低,排气温度将()。污氮气穿过水冷塔后,水温降低的原因有()。(1)污氮温度较低,要吸收一部分水的热量,致使水温降低。(2)污氮干燥度很高,有一部分水气化进入污氮气,水在气化过程重要吸
- 在双级精馏塔内,温度的分布情况是()。氩富集区的上移,氩馏分的含氮量将()。在积液阶段适当()上塔压力,有利于液体的迅速积累。氮纯度越高,上塔顶部温度()。自上而下温度升高#
自上而下温度降低
自上而下温度
- 空气节流后()不变。下塔回流比适当减小,则富氧液空纯度()。焓#
熵
温度降低
提高#
不变
无法确定
- 在上塔精馏段氩富集区气相氩含量比液相氩含量()。污氮气穿过水冷塔后,水温降低的原因有()。(1)污氮温度较低,要吸收一部分水的热量,致使水温降低。(2)污氮干燥度很高,有一部分水气化进入污氮气,水在气化过程
- 氩富集区的下移,氩馏分的含氧量将()。降低#
不变
提高
无法确定
- 气体在压缩机内,排气压力降低,排气温度将()。冷损包括:()。氩富集区的上移,氩馏分的含氮量将()。降低#
升高
不变
无法确定热交换不完全损失
跑冷损失
排液冷损
以上都是#降低#
不变
提高
无法确定
- 随着板式换热器热端温差的减小,则复热不足冷损()。下塔回流比减小,则氮气纯度()。越大
越小#
不变
无法确定降低#
提高
不变
无法确定
- 上塔顶部温度是由()确定的。在上塔存在氩富集区,但氩馏分抽口设在()。氧纯度和上塔底部压力
氮纯度和上塔底部压力
氮纯度和上塔顶部压力#
氧纯度和上塔顶部压力精馏段氩含量最大的部位
提馏段氩含量最大位置稍偏
- 随着上塔压力的降低,将()氧氮的分离。不利于
恶化
有利于#
无法确定
- 如果进塔空气量以及氧产量不变,氮纯度降低,则氧气纯度将()。若氩馏分含氮量过高会()。在上塔存在两个氩富集区,氩馏分抽口设在()。压力越高,上塔顶部温度()。下塔回流比适当减小,则富氧液空纯度()。降低#
- 氧纯度越低,上塔底部温度()。在精馏塔内,随着压力的降低,气相与液相之间的浓度差将()。氩富集区的下移,氩馏分的含氧量将()。越低#
越高
不变
无法确定减少
增加#
不变
无法确定降低#
不变
提高
无法确定
- 在上塔提馏段氩富集区气相氩含量比液相氩含量()。大#
小
一样
无法确定
- 如果进塔空气量以及氧产量不变,污氮纯度降低,则氧气纯度将()。混合物中,水温降低的原因有()。(1)污氮温度较低,要吸收一部分水的热量,有一部分水气化进入污氮气,水在气化过程重要吸收气化潜热,随着压力的降低,
- 混合物中,其组分的饱和蒸汽压的大小与()有关。(1)饱和温度(2)该组分的挥发性(3)该组分的浓度(4)该组分的化学性质随着板式换热器热端温差的减小,则复热不足冷损()。(1)(2)(4)
(1)(3)(4)
(1
- 空气节流后()不变。焓#
熵
温度
- 下列说法中不影响液氧平均温度的是()。下列有关温度的说法不正确的是()。氮纯度#
主冷液氧高度
氧纯度
上塔底部压力温度表示物体的冷热程度。
气体的压力越高,则气体的液化温度也温度越高。
温度是物质分子热运
- 吸附过程包括()。透平膨胀机压缩比()可以提高膨胀机效率。上塔回流比适当减小,则氧气纯度()。化合过程和物理过程
化学过程和物理过程#
化合过程和化学过程
以上都不对升高#
降低
一样
无法比较降低
提高#
不变
- 塔板阻力主要由()组成。(1)干塔板阻力,(2)液体表面张力阻力,(3)静液柱压力阻力。(1),(3)
(1),(2)
(2),(3)
(1),(2),(3)#
- 吸附剂的吸附容量与气流速度有关,气体流速越大,吸附效果()。空分装置容量越大,单位加工空气量跑冷损失()。在精馏塔内,随着压力的降低,气相与液相之间的浓度差将()。越好
越差#
不变
无法确定越大
越小#
不变
- 如果出现液氮纯度很高,而气氮纯度比液氮纯度还低的现象,则说明()。上塔回流比适当减小,则氧气纯度()。氧产量太多
导入上塔的液空量太少
导入上塔的液氮量太多
导入上塔的液氮量太少#降低
提高#
不变
无法确定
- 如果氮气取出量过大,则氮气纯度将()。下列说法中不影响液氧平均温度的是()。提高
不变
降低#
无法确定氮纯度#
主冷液氧高度
氧纯度
上塔底部压力
- 切换式板式换热器流程中,下列说法正确的是()。用烧碱除去空气中二氧化碳的过程属于()。适当()透平膨胀机前温度,可以提高膨胀机效率。只要满足二氧化碳自清除,就能满足水份自清除#
只要满足水份自清除,就能满足
- 有氧、氮组成的空气混合物在分离过程中,当压力提高时,气、液相中氮(或氧)的浓度差将()。如果进塔空气量以及氧产量不变,氮纯度降低,则氧气纯度将()。气体流速越大,吸附剂吸的附效果()。B降低#
提高
不变
无法
- 真空度等于()。空气通过膨胀机后()降低。分子筛吸附二氧化碳的过程属于()。空气节流后()。(1)焓不变(2)焓增加(3)温度降低(4)压力降低绝对压力减去大气压力
大气压力减去绝对压力#
绝对压力减去表压
- 与跑冷损失大小有关的正确的说法是()。空气在密闭容器内液化,随着液化过程的进行,下塔压力随液氧纯度的升高而()。污氮气穿过水冷塔后,水温降低的原因有()。(1)污氮温度较低,要吸收一部分水的热量,致使水温降
- 适当提高氧纯度,可引起氩富集区的()。氩富集区的上移,氩馏分的含氮量将()。上移降低#
不变
提高
无法确定
- 氮、氩两种组分组成的混合物,氮对氩来说是()。空气通过膨胀机后()不变。易挥发组分焓
熵#
温度
- 主冷温差一定时,下塔压力随氮纯度降低而()。空气在密闭容器内液化,随着液化过程的进行,空气的液化温度将()。空分装置容量越大,单位加工空气量跑冷损失()。降低降低#
升高
不变
无法确定越大
越小#
不变
无法确
- 上塔压力(),越有利于氧氮的分离。氩富集区的上移,氩馏分的含氮量将()。与跑冷损失大小有关的正确的说法是()。越低降低#
不变
提高
无法确定空分装置运转的时间
空分装置的容量与形式#
空分装置的占地面积
调节
- 空分装置容量越大,单位加工空气量跑冷损失()。当主冷温差一定时,下塔压力随氮纯度的降低而()。越大
越小#
不变
无法确定降低#
升高
不变
无法确定
- 下塔回流比适当增加,则下塔顶部氮气纯度()。上塔压力降低,下列说法不正确的是:()。热力学温标的基准点是()。降低
提高#
不变
无法确定可改善上、下塔的精馏工况
可增加氧产量。
单位制氧能耗将升高#
有利于氧
- 上塔顶部温度是由()确定的。空气节流后()降低。制氧机在高原地区气压较低时,空压机排气量()。压力越高,上塔顶部温度()。氧纯度和上塔底部压力
氮纯度和上塔底部压力
氮纯度和上塔顶部压力#
氧纯度和上塔顶部
- 主冷液氧面的(),有利于降低下塔压力。膨胀机的单位制冷量下列因素有关:()。(1)机前压力(2)机前温度(3)机后压力(4)膨胀机效率。随着膨胀机机前温度的升高,膨胀机前后温差将()。空气节流后()不变。降
- 空气节流后焓不变,()降低。膨胀机的单位制冷量下列因素有关:()。(1)机前压力(2)机前温度(3)机后压力(4)膨胀机效率。空气节流后()不变。氮纯度越高,上塔顶部温度()。温度(1)(2)
(3)(4)
(2
- 分子筛对空气中的水分、CO2和乙炔的亲和力最大的是()。空分装置容量越大,单位加工空气量跑冷损失()。随着上塔压力的降低,将()氧氮的分离。水分越大
越小#
不变
无法确定不利于
恶化
有利于#
无法确定