查看所有试题
- 在西门子STEP7中,()包括块调用指令以及通过主控继电器实现程序段使能控制的指令。在精密精馏时可采用()控制。A、逻辑控制指令
B、赋值指令
C、程序控制指令#
D、状态位指令A、恒温控制
B、差压控制
C、温差控制#
- 根据下图写出传递函数式,正确的表达式是()。数字显示仪表的非线性补偿方法之一,是先把被测参数的模拟量经模-数转换成数字量后再进入非线性补偿环节,这种方法叫做()。下式为二阶有纯滞后特性的微分方程一般表达
- 方块图中常用符号有分叉点。根据需要,把()信号同时送至几个不同的方块,可以在信号线上任意一点分叉。仪表自动化工程的试运行时仪表专业的主要任务有()。下面两式均为二阶环节微分方程式的一般数学表达式:公式中
- 钢铁发生腐蚀时,正极上发生的反应为()。仪表自动化工程设计的基本程序分前期和()二个阶段。HRAT网络中信号发生单元包括()。A、2Fe-4e-=2Fe2+
B、2Fe2++4e-=2Fe
C、2H2O+O2+4e-=4OH-#
D、Fe3++e
- 氨合成工序()是最关键的工艺参数之一,它控制的好坏与生产安全和全装置的经济效益直接相关。按照IUPAC的电化学分析分类方法,属于有电极反应并施加恒定激发信号的是()。在原料一定时影响裂解深度或乙烯收率主要取
- 集散控制系统机柜的安装要求与常规仪表箱安装要求相比,前者安装要求()。OPCDX数据交换、OPCXML扩展标识访问技术,适应了()技术的发展。PROFIBUS总线标准由()等几部分组成。A、更低
B、相同
C、不确定
D、更高#A
- 方块图的负反馈环节的运算方法是:具有负反馈环节总传递函数等于正向通道的传递函数除以()传递函数的乘积。雷电流静电感应可使被击物导体感生出与雷电性质相反的大量(),当雷电消失来不及流散时,即会产生很高电压
- 所谓对象的特性,是指被控对象的输出变量与输入变量之间随()变化的规律。引起离心式压缩机喘振因素有()。A、过渡时间
B、上升时间
C、滞后时间
D、时间#A、转速
B、被压缩气体的吸入状态#
C、压缩机负荷#
D、吸入
- 调节阀的流量系数与阀芯和阀座的结构、阀前阀后压差、()等因素有关。关于避雷针的作用描述正确的是()。数字式仪表的所谓“采样”表述,下面正确的是()。A、流体黏度
B、流体温度
C、流体密度
D、流体性质#A、避免
- 按照IUPAC的电化学分析分类方法,电导滴定属于()。催化裂化装置中多变量预测控制器的变量的选取都应()。动态矩阵控制中,干扰变量DV是不受控制器控制的变量,以下对它的描述正确的是()。A、没有电双层和电极反应#
- 微分环节的微分方程一般表达式为()。TDC3000系统的HPM状态表中,如HLAI卡的状态参数为IDLE,则表示此卡件()。设备设计和施工图设计是属于()。A、A
B、B
C、C#
D、DA、空载状态#
B、故障状态
C、组态错误
D、正常
- 一阶环节的特征参数是放大系数K和时间常数T,其数值的大小,直接影响环节输出的()。CAN技术规范2.0B遵循ISO/OSI标准模型,分为()。数字式仪表的电压-频率型模-数转换器由积分器和()等部分组成。A、幅值大小#
B
- 对于直线特性阀,最大开度应(),最小开度应()。A、≤80%,≥30%
B、≤80%,≥10%#
C、≤90%,≥30%
D、≤90%,≥10%
- 数字式仪表的所谓“采样”表述之一,就是把连续时间的波形X(t),用它在()时刻上的值X(1T)、X(2T)、X(3T)………来代替。下列关于铜电极的叙述中正确的是()。化学反应器最重要的被控变量是反应温度,控制住反应温
- 环节的特性是,当输入信号加入环节后,其输出信号()变化的规律。TDC3000系统的HPM状态表中,如HLAI卡的状态参数为IDLE,则表示此卡件()。A、按指数
B、按比例积分微分
C、随时间#
D、随控制条件A、空载状态#
B、故障
- 变压器在工作时,铁芯和绕组都会发热,所以必须采取冷却措施。对于小容量变压器多采用()方式。一阶环节的放大系数K是个()参数。TDC3000系统控制组态时,如组态一个PID单回路控制算法,则AO点应该组态为()。A、空气