查看所有试题
- 电气隔离的主要方法为()。频率合成器与其它信号发生器相比,主要特点是()。变压器耦合或光电隔离#
箝位电路
阻容耦合
移位电路精度高
输出稳定
价格便宜
精度高范围宽#
- 空芯线圈插入铜芯后,其电感量将()。增大
减小#
不变
不确定
- 高精度串联调整电源中,辅助电源的作用是()。甲类功放的静态工作点应放在()。稳定放大电路的工作电压#
稳定基准电路
提高小电压检测能力
改善调节能力直流负载线下端
直流负载线上端
直流负载线中点#
交流负载线
- 家用电度表用于计量()桥式整流与双管全波整流相比,其主要特点是()。A、功率;
B、电流;
C、电压;
D、功#A.效率高
B.只需要单次级绕组#
C.输出波形好
D.对整流器要求低
- 电子元器件可以划分为两大类:一类称为线性元器件,另一类称为非线性元器件.分类标准是根据它们的()A、频率特性曲线;
B、耐压特性曲线;
C、伏安特性曲线;#
D、温度特性曲线
- 如钽电容引线有熔接点,弯曲点不允许在熔接点和元器件之间,熔接点到弯曲点之间应保留()距离合适。放大器对信号源影响小,则表明放大器的输入电阻()1mm
2mm#
3mm
4mmA.很小
B.很大#
C.很稳定
D.无法确定
- 镀镍的涂覆标记是()A、D.Ag;
B、D.Cr;
C、D.Zn;
D、D.Ni#
- ±1个字误差属于()误差。距离发射机用于产生射频脉冲,然后将其馈送到()上。仪器误差
环境误差
人为误差
固有误差#A、测距天线#
B、接收机
C、方位基准天线
D、监测天线
- 某电容的实体上标识为1n表示为()A、1000PF±20%;#
B、1000UF±20%;
C、1PF±10%;
D、1UF±10%;
- 通常电子手工焊接时间为()A、越长越好;
B、越短越好;
C、2~3秒;#
D、2~3分
- 对推挽放大器而言,()结论是正确的。因两管轮流工作,必然存在交越失真
只要保证两管都工作在放大状态,即可保证输出不失真
使两管有合适的偏流,即可消除交越失真#
其功放要比单管功放低
- 3.9千欧等于()VCD视盘机的机芯与()机相似.A、0.39兆欧;
B、39欧;
C、390欧;
D、3900欧#A、LD
B、CD;#
C、电唱机
D、磁带机
- 三用表进行电阻测量时,指针在()位置,测量精度最高。靠左边
靠右边
在中间位置#
任意
- 搪锡高度距元器件引线根部大约是()。1mm
2mm#
3mm
4mm
- 能够为负载提供足够大功率的放大电路称为()。交流放大电路;
直流放大电路;
电压放大电路;
功率放大电路。#
- 把母材不熔化的焊接称为()A、电弧焊;
B、钎焊;#
C、激光焊;
D、气焊