查看所有试题
- 直流基础电源是指()组成的直流供电系统。常用的高压电器有()。A、整流器#
B、蓄电池#
C、监控设备#
D、直流配电设备#A、高压熔断品#
B、高压断路器#
C、高压隔离开关#
D、高压负荷开关#
- 为安全供电,专用高压输电线和电力变压器()。相控整流器不宜长期工作在小于额定电流值()的状态下。交流电的频率允许变动范围为额定值的()。二级过电压保护器通常采用()kA(8/20μs波形)的氧化锌保护器,一般安
- 直流电源供电的质量指标:直流供电回路接头压降(直流配电屏以外的接头)应符合下列要求,或温升不超过50℃。直流电流在1000A以下,每百安培()mv。3
4#
5
6
- 交流电的频率允许变动范围为额定值的()。开关电源具有功率因数高的特点。一般高频开关电源的功率因数大于(),在有功率因数校正电路时,功率因数接近1,因而对公共电网不会造成污染。A、±3%
B、±4%#
C、±5%
D、±6%0.
- 通信设备用交流电供电时,在通信设备的电源输人端子处测量的电压允许变动范围为额定电压值的()。发电机组的容量配臵:对交流不间断电源(UPS)供电时,其容量应按不小于UPS设备总容量的()倍。。A、-5%~+5%
B、
- 交流电的电压波形正弦畸变率应为()。交流电源系统对通信局提供的建筑一般负荷用电是指()。电流互感器在正常工作状态时,接近于变压器的()状态。通信设备直流基础电源电压为()。()架设在架空线路的上边,用以
- 相控整流器不宜长期工作在小于额定电流值()的状态下。A、10%#
B、20%
C、30%
D、40%
- DC/AC变换是()。各种大小或类型的信号接入采集器时,需要的设备是()。直流/直流变换器
整流器
逆变器#
变压器接口转换器
协议处理器
传感器#
服务器
- 通信电源设备及重要建筑用电设备用交流电供电时,在设备的电源输人端子处测量的电压允许变动范围为额定电压值的()。为安全供电,专用高压输电线和电力变压器()。交流不间断电源由()等部分组成。DC/AC变换是()
- 每次起动时间不能过长:起动操作时间过长,会引起起动电动机过热而损坏,长时间大电流以也易损坏蓄电池,因此对每次的起动时间加以限制,一般为()秒。通信电源系统目前主要使用的蓄电池为()。3—5
5—10#
15—30开口电
- 同轴型SPD的标称放电电流应大于等于()kA。A、5#
B、4
C、3
- 为安全供电,专用高压输电线和电力变压器()。常用的高压电器有()。A、不得让外单位搭接负荷#
B、经主管部门批准可以让外单位搭接负荷
C、可以让外单位搭接负荷
D、经主管部门批准可以允许有关单位搭接负荷A、高压
- 电流互感器在正常工作状态时,接近于变压器的()状态。电力电容器是电力系统中经常使用的设备,它的重要作用是()在线路上以提高线路上的功率因数。开路
短路#
过载串联
并联#
混联
- 电力电容器是电力系统中经常使用的设备,它的重要作用是()在线路上以提高线路上的功率因数。开关电源系统中,可以通过()标准通信接口连接本地计算机,亦可通过Modem或其他传输资源连接到远程监控中心,实现电源系统
- 发电机的额定电压比电网电压高()是考虑到负荷电流导致在线路上产生压降损失。高压断路器()带负荷操作当外电路断开即没有电流通过电池时,在正、负极间的电位差,叫做电池的()。接地体埋深一般不小于()m(接地
- 在通信电源系统中,常用的SPD有开关型和限压型两种,下面哪种属于限压型的SPD()。为了确保基站内设备不因直流拉远馈电线将雷电引入,损坏设备,机房内必须在直流拉远馈电线处安装直流配电防雷箱,不管厂家是否称接口有
- 二级过电压保护器通常采用()kA(8/20μs波形)的氧化锌保护器,一般安装在电源柜内的电源入口处。它的主要作用是降低一级过电压保护器的雷电残压,消除一、二级保护器间线路感应的雷电过压,防止地网的电位不平衡。A、
- 二级过电压保护器通常采用()kA(8/20μs波形)的氧化锌保护器,一般安装在电源柜内的电源入口处。它的主要作用是降低一级过电压保护器的雷电残压,消除一、二级保护器间线路感应的雷电过压,防止地网的电位不平衡。A、
- 交流用电设备采用三相四线制引入时,零线()。常用的高压电器有()。低压交流电的标称电压为()伏,三相五线,可以通过()标准通信接口连接本地计算机,亦可通过Modem或其他传输资源连接到远程监控中心,实现电源系统
- 常用的高压电器有()。二级过电压保护器通常采用()kA(8/20μs波形)的氧化锌保护器,一般安装在电源柜内的电源入口处。它的主要作用是降低一级过电压保护器的雷电残压,消除一、二级保护器间线路感应的雷电过压,防
- 相控整流器不宜长期工作在小于额定电流值()的状态下。UPS电源电气性能表中规定:频率跟踪范围在()%以内可调。()架设在架空线路的上边,用以保护架空线路或其他物体(包括建筑物)免受直接雷击。接地系统中的垂
- 通信电源设备及重要建筑用电设备用交流电供电时,在设备的电源输人端子处测量的电压允许变动范围为额定电压值的()。交流用电设备采用三相四线制引入时,零线()。电力电容器是电力系统中经常使用的设备,它的重要作
- 发电机组的起动间隔时间要求:第一次起不成功后,必须等待一段时间,消除蓄电池的浓差极化,通常所说的蓄电池的恢复时间。一般为()秒。直流供电系统中在正常情况下,蓄电池处于()。直流电源供电的质量指标:直流供电
- 变流设备包括()。A、相控整流器#
B、开关整流器#
C、直流变换器#
D、逆变器#
- 交流用电设备采用三相四线制引入时,零线()。交流电源系统对通信局提供的建筑一般负荷用电是指()。常用的高压电器有()。变流设备包括()。低压交流电的标称电压为()伏,三相五线,频率50赫兹。电流互感器在正
- 交流电源系统对通信局提供的保证建筑负荷用电是指()等设备的用电。监控系统对非电量的测量精度一般应优于()。A、通信用空调设备#
B、保证照明#
C、消防电梯#
D、消防水泵#0.5%
1%
2%
5%#
- 开关电源模块采用()方式对用电负荷进行供电。我国规定安全电压系列的上限值在正常和故障情况下,两导体间或任一导体与地之间的电压,均不得超过交流有效值()V空载上限值的规定。并联#
串联
级联
复联A、30
B、50#
- 发电机组的容量配臵:对交流不间断电源(UPS)供电时,其容量应按不小于UPS设备总容量的()倍。。1.5~2#
1~1.4
2~2.5
- 交流用电设备采用三相四线制引入时,零线()。熔断器的温度应低于()。常用的高压电器有()。交流配电屏输出负荷分路可根据不同()的需求而定。A、不准安装熔断器#
B、必须安装熔断器
C、装与不装熔断器均可
D、
- 每次起动时间不能过长:起动操作时间过长,会引起起动电动机过热而损坏,长时间大电流以也易损坏蓄电池,因此对每次的起动时间加以限制,一般为()秒。动力环境集中监控管理软件是属于()。3—5
5—10#
15—30A、系统软件
- 发电机组的容量配臵:对交流不间断电源(UPS)供电时,其容量应按不小于UPS设备总容量的()倍。。()架设在架空线路的上边,用以保护架空线路或其他物体(包括建筑物)免受直接雷击。为了确保基站内设备不因直流拉远
- 熔断器的温度应低于()。低压交流电的标称电压为()伏,三相五线,频率50赫兹。DC/AC变换是()。对开关进行绝缘电阻测试,试验电压为直流500V时,整流器主回路的交流部分和直流部分对地以及交流部分对直流部分的绝缘
- 发电机组的容量配臵:对交流不间断电源(UPS)供电时,其容量应按不小于UPS设备总容量的()倍。。直流电源供电的质量指标:直流供电回路接头压降(直流配电屏以外的接头)应符合下列要求,或温升不超过50℃。直流电流
- 直流基础电源的基础电压范围内的工作电压有()。对直流配电屏中的测量熔断器的温升或压降,应每()进行。A、浮充电压#
B、均衡电压#
C、终止电压#
D、充电电压月#
季
半年
年
- 我国目前采用的输变电标准电压有()和110kV。高压断路器()带负荷操作发电机组的起动间隔时间要求:第一次起不成功后,必须等待一段时间,消除蓄电池的浓差极化,通常所说的蓄电池的恢复时间。一般为()秒。直流电源
- 直流基础电源的基础电压范围内的工作电压有()。常用的高压电器有()。变流设备包括()。交流不间断电源由()等部分组成。直流供电系统中在正常情况下,蓄电池处于()。监控系统发现监控对象故障应及时告警,从故
- 通信设备用交流电供电时,在通信设备的电源输人端子处测量的电压允许变动范围为额定电压值的()。直流供电系统中,当市电(故障)停电而油机未启动供电前,由()放电向通信设备提供直流不间断供电。当外电路断开即没
- 每次起动时间不能过长:起动操作时间过长,会引起起动电动机过热而损坏,长时间大电流以也易损坏蓄电池,因此对每次的起动时间加以限制,一般为()秒。3—5
5—10#
15—30
- 对开关进行绝缘电阻测试,试验电压为直流500V时,整流器主回路的交流部分和直流部分对地以及交流部分对直流部分的绝缘电阻均不低于()MΩ。1
2#
3
5
- 我国规定安全电压系列的上限值在正常和故障情况下,两导体间或任一导体与地之间的电压,均不得超过交流有效值()V空载上限值的规定。UPS电源电气性能表中规定:频率跟踪范围在()%以内可调。A、30
B、50#
C、8050Hz±