查看所有试题
- 为了便于维修,控制台背面距墙净空不少于()m.A.0.8B.1C.1.2D.1.5
- JT-C主机板内部若点灯继电器故障,将导致()。ZPW-2000A无绝缘移频自动闭塞系统正线检测盘的型号是()。灭灯
点亮红灯
点亮白灯
主机返回复位自检#A.ZPW·ZXJB.ZPW·PJZC.ZPW·JZD.ZPW·PJC
- 当列车速度超过允许速度.但未超过最大常用制动速度时,CTCS-2列控系统车载设备DMI显示屏中从允许速度到SBI之间光带的宽度为正常光带宽度的两倍,显示颜色为()。A.蓝色B.深灰色C.红色D.橙色
- 6502电气集中12线网络接SJ第五组接点的作用是()。TDCS机柜采样控制板将采集到的信息通过串口()发送到通信机的多串口上。A.防止道岔提前解锁B.防止迂回电流C.保证供电D.防止错误办理故障解锁#A.COM1B.COM2C.并口1
- 四线制道岔(三相交流除外)表示电路中二极管的技术指标是()。A.反向电压不小于500V,正向电流不小于300mAB.反向电压不大于500V,正向电流不大于300mAC.反向电压不小于1000V,正向电流不小于300mAD.反向电压不大于500
- 在ZPW-2000Hz区段机车信号显示B灯,接收的输入信号为()。29Hz
11.4Hz
10.3Hz
无码#
- 为了便于维修,控制台背面距墙净空不少于()m.A.0.8B.1C.1.2D.1.5
- 对于JTl-CZ2000型机车信号的非点灯信号,采用()输出方式。A.直接B.光耦C.继电器D.变压器
- 排列以调车信号机按钮为变通按钮的列车变通进路时,方向继电器有()自闭电路。最早的采用微机控制机车信号是为了解决()的问题。A.1条B.2条C.3条D.4条模拟设备参数一致性差
干扰难以排除
应变速度不足
多制式通用#
- TDCS机柜采样控制板将采集到的信息通过串口()发送到通信机的多串口上。具有1/2式芽序的树木是()。A.COM1B.COM2C.并口1D.并口2#紫荆
国槐
垂柳
榆树#
- 6502电器集在12线上串接QJJ第二组接点的作用是()。JT-C机车信号主机,接收3060新标准UM71制式,主机板如何设置().A.防止提前解锁B.防止道岔中途转换C.防止迂回电流D.保证供电F短路、J、Z、G断开#
F断开、J、Z、G短
- ()实质上是由一只电流互感器、钳形扳手和一只整流式磁电系有反作用力仪表所组成。固定切换方式的站内电码化的发码时机终止于()。A.电流表B.万用表C.数字衰D.钳形表A.列车驶入本区段B.列车出清本区段C.列车完全进
- 要立足企业运营,大力推进管控标准化。统一度量衡是组织赖以存在的基础也是提高组织运转效率的关键。全局范围内各管理线条统一管控模式,系统优化提升管理,满足内控审计、贯标认证、信息化管理等各方面的要求,在公司治
- JTl型通用式机车信号主机板上的点灯继电器使用()电源。A.5VB.12VC.24VD.50V#