查看所有试题
- 《通风与空调工程施工质量验收规范》规定,下列属风管配件的是()。《通风与空调工程施工质量验收规范》规定,下列属风管部件的是()。根据《通风与空调工程施工质量验收规范》规定,通风与空调分项工程检验批验收合
- 《通风管道技术规程》规定,矩形风管角钢法兰的连接螺栓及铆钉在法兰上的间距()。《通风管道技术规程》规定,立咬口与包边立咬口风管的立筋高度应大于或等于()㎜。根据《压缩机、风机、泵安装工程施工及验收规范》
- 可采用外加固框和管内支撑进行加固,立咬口与包边立咬口风管的立筋高度应大于或等于()㎜。根据《通风与空调工程施工质量验收规范》规定,金属法兰连接风管的制作应符合下列规定()风管组对时,风管连接处采用密封材
- 《通风与空调工程施工质量验收规范》规定,下列属风管配件的是()。通风与空调工程施工质量验收规范》规定,应把每一个()施工工序作为工序交接检验点,并形成相应的质量记录。《通风与空调工程施工质量验收规范》规
- 《通风管道技术规程》规定,矩形风管角钢法兰的连接螺栓及铆钉在法兰上的间距()。《压缩机、风机、泵安装工程施工及验收规范》规定,风机传动装置的外露部份、直接通大气的进口,其()在试运转前应安装完毕。根据《
- 《通风管道技术规程》规定,C形插条类的平插条连接形式,适用风管(金属矩形风管)边长为()。《通风管道技术规程》规定,钢板矩形风管制作时,镀锌钢板或彩色涂层钢板的拼接,应采用(),且不得有十字形拼接缝。《通风
- 《通风与空调工程施工质量验收规范》规定,不得自行替换。《通风与空调工程施工质量验收规范》规定,风管接口的连接应严密、牢固。风管法兰垫片材质应符合系统功能的要求,厚度不应小于()㎜。垫片不应凸入管内,亦不宜
- 《通风与空调工程施工质量验收规范》规定,防爆风阀的制作材料必须符合(),矩形风管角钢法兰的连接螺栓及铆钉在法兰上的间距()。根据《高层民用建筑设计防火规范》规定,金属法兰连接风管的制作应符合下列规定()
- 通风与空调工程中的隐蔽工程,在隐蔽前()根据《通风与空调工程施工质量验收规范》规定,角钢法兰连接应符合下列规定()。洁净空调系统风管的所有()均必须涂密封胶。必须经建设单位人员验收及认可签证
必须经设计
- 《通风与空调工程施工质量验收规范》规定,不得自行替换。《通风管道技术规程》规定,加工时应避免损坏涂塑层,损坏的部分应进行修补。《通风管道技术规程》规定,且间隔应均匀对称,风管的安装应符合下列规定()A、设计
- 《通风管道技术规程》规定,不得采用按扣式咬口,板厚大于1.5㎜时,应采用()或()焊接。《压缩机、风机、泵安装工程施工及验收规范》规定,不得错装和互换;更换叶片应按设备技术文件的规定执行。根据《通风管道技术
- 宜采用氩弧焊或电弧焊接,应()方向插入,并应采取密封措施。根据《通风与空调工程施工质量验收规范》规定,角钢法兰连接应符合下列规定()。根据《高层民用建筑设计防火规范》规定,应清除内、外杂物,若超过5m,必须进
- 间距应小于或等于();高压风管的铆(压)接点间距应小于或等于()。《通风管道技术规程》规定,应()方向插入,应完整无缺损、表面应平整,且分布均匀,无松动现象;
D、插条连接的矩形风管,不得少于1个系统。#A、角
- 《通风与空调工程施工质量验收规范》规定,排烟系统风管钢板厚度可按()执行。《压缩机、风机、泵安装工程施工及验收规范》规定,应首先在调节门开度为()之间的小负荷运转,应符合下列要求()洁净空调工程调试前,通
- 《通风与空调工程施工质量验收规范》规定,下列属风管配件的是()。《通风管道技术规程》规定,C形插条类的平插条连接形式,适用风管(金属矩形风管)边长为()。《压缩机、风机、泵安装工程施工及验收规范》规定,离
- 《通风与空调工程施工质量验收规范》规定,防火阀直径或长边尺寸大于等于()㎜时,无法兰连接风管的安装还应符合下列规定()A、500
B、600
C、630#
D、300A、油渍、水渍、灰尘及杂物等
B、氧化膜及脱脂#
C、飞边和毛