查看所有试题
- 由于pH值受水温影响而变化,测定时应在现场快速测定。文字描述法检测水中臭时,采样后应尽快检测,最好在样品采集后小时内完成()用文字描述法检验水样中臭的原理是:检验人员依靠自己的嗅觉,在()和()闻其臭,用适
- 电化学探头法测定水中溶解氧时,所用的电极分两种类型,所用的便携式浊度计()用()度的标准溶液进行校准。目视比色法测定浊度时,水样必须经后方可测定。用浮标法进行污水流量测量时,排污口上溯有一段底壁平滑且长度
- 电极法测定水的氧化还原电位时,用于校正空白电极的标准溶液的名称是()。硫酸亚铁铵-硫酸高铁铵标准溶液
- 电极法测定水的氧化还原电位,在校验指示电极时,如实测结果与标准电位值相差大于()mV,则指示电极需要重新净化或更换。臭阀值法检验水中臭时,至少()人,最好()人或更多,方可获是精度较高的结果。()±105,10#
2,6
- 电极法测定水的氧化还原电位时,配制试剂用水的电导率应小于()μS/cm,即将去离子水煮沸数分钟,以驱除水中的二氧化碳气体,然后()。2;密塞冷却
- 测量水的pH值时,应适当进行搅拌,以使溶液均匀并达到电化学平衡,而在读数时,则应(),(),以使读数稳定。用塞氏盘法在现场测定水的透明度时,正确方法是将盘在船的()处平放水中。停止搅动;静置片刻直射光
背光#
迎
- 用浮标法进行污水流量测量时,确定检验臭阀值的人数视检测目的、检测费用和选定检臭人员等条件而定。一般情况下,至少()人,方可获是精度较高的结果。()用塞氏盘法在现场测定水的透明度时,正确方法是将盘在船的()
- 浮标法测流时所用水面浮标,其入水部分表面应较粗糙,不应成流线型。浮标下面要加系重物,保持浮标在水中漂流稳定。浮标的入水深度,在()和()闻其臭,用适当的词句描述臭特性,并按等级报告臭强度。()用塞氏盘法在现
- 流速仪法测水的流速时,测点的分布应符合一条垂线上相邻两测点的最小间距不宜()流速仪旋桨或旋杯的直径。测水面流速时,并应使仪器旋转部分的边缘离开河底2~5cm。使用十字法测定水的透明度时,水样必须经后方可测定
- 采用浓度法测水流量时,要用较多的示踪物质,因此,采用此法时要充分考虑到这些物质对(),尤其是对鱼类的影响。铅字法测定水的透明度时,使用的透明度计必须保持洁净,观察者应记录()时水柱的高度。A.水生生物#
B.水
- 使用流速计测量水的流量时,应将探头放入管道或渠道的()H处。测量的时间越长,所测量流速越准确,测量的时间应大于()s(H为水的深度,m)。A.0.5,100
B.0.6,50
C.0.6,100#
D.0.3,100
- 如果废水在封闭型圆形管道中流动,且充满管道,其平均流速则是主轴线流速的()。十字法测定水的透明度,准确记录水柱高度是在()为止。十字法测定水的透明度,将水样先倒入透明度计至黑色十字完全消失,除去气泡,将水样
- 实行总量监测的企事业单位的排污口,必须安装符合有关技术要求的自动污水流量测量装置,所选择污水流量装置必须适应于污水特性和污水排放。文字描述法检测水中臭时,采样后应尽快检测,最好在样品采集后()h内完成。正
- 污水流量测量应能满足水污染物排放总量监测的需要,污水测流须与污染物浓度监测同步。正确#
错误
- 在每次使用流速仪之前,必须检查仪器有无污损、变形,仪器旋转是否灵活及接触丝与信号是否正常等。下列气体中会干扰电化学探头法测定水中溶解氧的是:()。正确#
错误A.C02#
B.U2
C.N2
D.CO
- 容器法测定污水流量,适用于流量小于每日100t的排放口,并要求污水溢流口与受纳水体应有适当落差或能用导水管形成落差。便携式浊度计法测定水的浊度时,用()将比色皿冲洗两次,然后将待测水样沿着比色皿的边缘缓慢倒入
- 要求/顷直段的长度应大于上、下浮标断面间距的两倍。浮标中断面应有代表性,并无大的串沟、回流发生。臭阀值法检验水中臭时,确定检验臭阀值的人数视检测目的、检测费用和选定检臭人员等条件而定。一般情况下,方可获
- 对穿过岩石而流出的溪流来说,河流断面和流速分布都很不规则,用一般方法测定流量比较困难,此情况下水体的混合状态良好,适宜于用流速计法测定流量。用文字描述法检验水样中臭的原理是:检验人员依靠自己的嗅觉,在和(
- 溢流堰法测定水流量使用的薄壁堰,根据堰口的形状,可分为三角堰、梯形堰和矩形堰3种,三角堰多用于测定较大的流量,梯形堰和矩形堰用于测定较小的流量。便携式浊度计法测定水的浊度时,用()将比色皿冲洗两次,然后将待
- 容积法测定污水的流量是将容器放在流水降落地点的同时,卡上秒表,测定容器中装至一定体积水所需的时间。测定一次,记录时间t(s),根据容器容量计算流量。正确#
错误应重复测定数次,求出时间的平均值,根据容器容量计算
- 流速计法测定水流速时,要把流速计沉降到指定深度,且把流速计置于正对着水流方向上测定,还应把流速计置于测定人的下游一侧,以避免测定人位置对测速的影响。下列气体中会干扰电化学探头法测定水中溶解氧的是:()。正
- 流速计法测定水的流速时,为减少测量误差,当水深小于40cm时,采用一点法,水深大于40cm时,采用两点法。正确#
错误
- 河道水草丛生或河底石块堆积影响正常测流时,应()、()。十字法测定水的透明度,将水样先倒入透明度计至黑色十字完全消失,除去气泡,将水样从筒内()放出,记录透明度厘米数。使用十字法测定水的透明度时,水柱高度超
- 流速仪法测流排污截面底部需硬质平滑,截面形状为规则的几何形,排污口处有不小于()m的平直过流水段,且水位高度不小于()m。用塞氏盘法在现场测定水的透明度时,正确方法是将盘在船的()处平放入水中。下列说法正确
- 《河流流量测验规范》(GB50179—1993)适用于天然河流、()、水库、()、潮汐影响和建设工程附近河段的流量测验。电化学探头法测定水中溶解氧时,仪器需要检验零点的时候,可将电极浸入()的蒸馏水中进行校零。湖泊
- 测流河段应选择在/顷直,稳定,水流集中,五分流、岔流、斜流、回流及死水等现象的河段。顺直河段长度应大于洪水时主河槽宽度的3倍。宜避开有()汇入或()及()等大水体产生变动回水的影响。臭阈值法检验水中臭时,
- 浮标法常用于推算和估计水渠或河段中的()流量或()期间的河水流量测量。目视比色法测定浊度时,用250度的浊度原液配制100度标准液500m1,需吸取ml浊度原液。浅水;洪水A.250
B.100
C.500
D.200#
- 溢流堰法是测量水流量的主要方法,所用的堰按堰顶的形式或堰壁厚度可分为薄壁堰、()和()。其中薄壁堰使用方法简单,精度较高,广泛使用于明渠测流,并可实现自动测量。用塞氏盘法在现场测定水的透明度时,正确方法是
- 水的流量测量方法有流速计法、()、()、容积法、孔板流量计、水平衡法、排水系数法、浓度法、皮托管测速计法、文丘里测速计法等多种方法。浮标法;溢流堰法;巴氏槽法;管道量水角尺法;无压管道及明渠流量测算法
- 当水深大于()cm、流速不小于()m/s时,可用流速计测量流速。常用的流速计有旋杯式和桨式两种。用文字描述法检验水样中臭的原理是:检验人员依靠自己的嗅觉,在()和()闻其臭,用适当的词句描述臭特性,并按等级报
- 用文字描述法检验水样中臭的原理是:检验人员依靠自己的嗅觉,在()和()闻其臭,用适当的词句描述臭特性,并按等级报告臭强度。()铅字法测定水的透明度时,使用的透明度计必须保持洁净,观察者应记录时水柱()的高
- 目视比色法测定浊度时,对浊度低于10度的水样进行比色时,浊度为10度以上的水样,比色时应()观察。文字描述法检测水中臭时,采样后应尽快检测,最好在样品采集后小时内完成()被测水体中含盐量在35g/L以下的时候,氧在
- 目视比色法测定浊度时,水样必须经后方可测定。便携式浊度计法测定浊度时,水样的浊度若超过()度,需进行稀释。A.静置24h
B.悬浮物沉降后
C.摇匀#A.10
B.50
C.100
D.40#
- 用文字描述法检验水样中臭的原理是:检验人员依靠自己的嗅觉,用适当的词句描述臭特性,所用的便携式浊度计()用()度的标准溶液进行校准。目视比色法测定浊度时,()观察,比色时应()观察。常温,10#
B.每季度,40
- 便携式浊度计法测定水的浊度时,用()将比色皿冲洗两次,然后将待测水样沿着比色皿的边缘缓慢倒入,以减少气泡产生。被测水体中含盐量在35g/L以下的时候,氧在水中的溶解度随含盐量的()。A.待测水样#
B.蒸馏水
C.
- 目视比色法测定浊度时,用250度的浊度原液配制100度标准液500m1,需吸取ml浊度原液。用文字描述法检验水样中臭的原理是:检验人员依靠自己的嗅觉,在()和()闻其臭,用适当的词句描述臭特性,并按等级报告臭强度。()
- 便携式浊度计法测定水的浊度时,所用的便携式浊度计()用()度的标准溶液进行校准。如果废水在封闭型圆形管道中流动,且充满管道,其平均流速则是主轴线流速的()。A.每月,10#
B.每季度,40
C.半年,0
D.每月,0A.
- 便携式浊度计法测定浊度时,水样的浊度若超过()度,需进行稀释。文字描述法检测水中臭时,采样后应尽快检测,最好在样品采集后小时内完成()目视比色法测定浊度时,水样必须经后方可测定。A.10
B.50
C.100
D.40#2
- 测定浊度的水样,可用具塞玻璃瓶采集,也可用塑料瓶采集。正确#
错误
- 在校准与测量过程中使用两个比色皿,其带来的误差可忽略不计。文字描述法检测水中臭时,采样后应尽快检测,最好在样品采集后小时内完成()铅字法测定水的透明度,还受照明条件的影响,检测结果最好取()用塞氏盘法在现