查看所有试题
- 游荡型河段河势急剧变化,常出现(),造成大溜顶冲堤岸,危及大堤安全。“横河”、“斜河”#
水流平稳
主流稳定
变化缓慢
- 洪江水情测报系统测报范围为()。采用YCZ-1A型设备的水情系统有()。A、芷江水文站以下
B、挂治大坝以下#
C、新晃水文站以下
D、靖县水文站以下A、五强溪水情测报系统
B、凌津滩水情测报系统
C、碗米坡水情测报系
- ()摩擦驱动装置轴承工作温度不得超过标准规定。选择好电动机保护器后进行更换时,应按照()的要求,安装接线。A、监听
B、手摸#
C、鼻闻
D、测量A、原产品接线
B、设计要求
C、产品说明书#
D、技术人员
- 卧式机组飞轮的作用是增加机组的()。A、重量
B、转速
C、稳定性#
D、安全性
- 按照灌溉水是否湿润整个农田、水输送到田间的方式和湿润土壤的方式,通常将灌溉分为全面灌溉和()两类。灌水方法
灌水技术
全面灌溉
局部灌溉#
- 标准规定,保护层达到设计强度后,应进行的检测。()防水层厚度
防水层构造做法
混凝土和卷材或涂料的粘结强度#
不透水性
- 推力头与主轴多采用()制过渡配合并热套主轴。A、基孔;
B、基轴;#
C、基孔或基轴;
D、公差配合。
- 屋面防水层上放置设施时,设施下部的防水层应增设附加增强层,还应在附加层上浇筑厚度大于()mm的细石混凝土保护层,附加层应比细石混凝土四周宽出100mm。A.20
B.50#
C.40
D.100
- 自记雨量计短时间发生故障,经邻站对照分析插补修正的资料()参加“各时段最大降水量表(1)”统计。如需要内插断沙量,一般先在其时段内由实测单沙内插未测期间的单沙,再由单沙与断沙关系推出相应断沙,而()直接由时
- 齿轮运转过程中检查齿轮啮合()。液压启闭机机架的横向中心线与实际起吊中心线的距离偏差不应超过()。A、不灵活
B、良好#
C、有冲击
D、不平稳A、±2mm#
B、±3mm
C、±4mm
D、±5mm
- 异常带电指()下不应当带电的生产设施或其中的部分意外带电,俗称“漏电”,从而造成人员伤害。A、极端情况
B、正常情况#
C、一般情况
D、特殊情况
- 隧洞洞身的哪种衬砌为不受力衬砌。()A、喷锚衬砌
B、预应力衬砌
C、平整衬砌#
D、单层衬砌
- 规划治导线一般以()作为中水治导线的设计流量。造床流量#
设计洪水流量
枯水流量
可能最大洪水流量
- 沉降点标志一般由()、立柱和标点头三部分组成。不属于常见穿堤建筑物的是()。底板#
木桩
土坑
保护盖跨河桥梁#
堤防涵闸
穿堤泵站
穿堤管道
- 建设跨堤建筑物不得()堤防安全、影响河势稳定、妨碍行洪畅通。巩固
提高
危害#
构成
- 堤岸防护工程的护脚工程一般都是()结构(也称为根石)。干砌石
散抛堆石#
混凝土
土质
- 水轮发电机组水导轴瓦正常运行温度是()A、20℃—30℃
B、30℃—40℃
C、45℃—60℃#
D、70℃
- 堤顶稍微不够平整的养护修整方法不包括()。土质堤防常用护坡措施不包括()。铲平
翻修#
整理
夯实草皮护坡
砌石护坡
混凝土护坡
合成材料护坡#
- 对堤岸防护工程顶部及土坝体顶的维修内容包括()。着手抢险以前,必须对()有正确的分析判断。树草治病除害#
归整残缺石垛#
拣整根石
恢复坍塌石垛#
顶部平整#导致该险情的因素#
奖励制度
险情类别#
险情规模#
险情
- 逐日水温表中的日值一般填写每日()的水温数值。逐日水温表编制挑选月最高、最低值及其发生日期时,应在全月()观测值中挑选。A、8时#
B、20时
C、8时与20时的平均值
D、8时与20时的最大值A、规定的8时
B、规定的20
- 水闸是一种低水头水工建筑物,具有()和启门泄水的双重作用。在自重或外力作用下坝岸整体或部分失稳,使护坡或连同部分土坝体沿滑动面(多为弧形面)向河内滑动,称为()。关门挡水#
漏水
渗水
抽水坝岸漫溢
坝岸坍塌
- 一般工程的施工进度计划常用()表示。工程维修必要图表包括工程观测有关图表、项目安排表、已完成()表等。横线
表格
图纸
横道图法#工程量#
长度
宽度
深度
- 将光标放在文件的图标上可以看出该文件的类型、()、修改日期和大小。标题#
全部内容
图片
数据
- 对混凝土护坡沉陷破坏的翻修内容不包括()。若混凝土路面沉陷严重,应将整块(),加固路基,重新浇筑混凝土路面。拆除破坏部位
全部翻修#
清除垫层
整修恢复土坡加高
衬平
破除#
抹平
- 普通式梁格的主梁数目较少,其间距和截面尺寸较大,一般在主梁之间设置有水平次梁。复式梁格的主梁数目更少,其间距和()也更大,中间设有垂直次梁和水平次梁A、面积
B、垂度
C、长度
D、截面尺寸#
- 抢险“三要素”包括工情、()和险情。工程基础
河势#
工程现状
险情类别
- 通常用()范围和距某特征位置的距离标定裂缝位置。通过观察保护层完好情况可推断穿堤建筑物与堤防接合部临水侧()是否完好。公里
百米
里程桩号#
米截水设施#
排水设施
反滤层
透水体
- 45#钢表示钢中平均含碳为(),机床上大部分零件都可用45#钢制成。加热后,管线内()的化学反应加快。A、45%
B、4.5%
C、0.45%#
D、0.045%A、腐蚀
B、结垢#
C、结锈
D、结蜡
- 冰情统计表中终冰日期是填写()出现冰情的日期。消光法分析颗粒级配,充分搅拌量筒中制备好的样品,停止搅拌的同时,随即用吸管吸取适量试样注入沉降盒内,加纯水至()刻度线并测记水温。A、上半年第一次
B、下半年第
- 在泵机组运行平稳时,采用流量法测泵效,()参数不需要记录。连杆螺栓螺母松动,可导致()出现敲击声。A、压力
B、流量
C、电压
D、温度#A、动力端#
B、液力端
C、进液阀
D、排液阀
- 脚手架的质量检查、验收,重点检查()项目,并需将检查结果记入验收报告。工业设计的制度化的进程,在荷兰的()得以发展。A、脚手架j架杆、配件设置和连接是否齐全,质量是否合格,构造是否符合要求,连接和挂扣是否紧固
- 在装配图中,滚动轴承这类零部件可采用示意画法和()画法等特殊表达方法。为完成活动或达到结果,提供客观证据的文件是()。A、假想
B、简化#
C、展开
D、夸大A、程序文件
B、作业文件
C、记录#
D、管理手册
- 铸造用的铝合金,主要是()合金。注水单耗的测定方法有()种。A、铝铜
B、铝镁
C、铝硅#
D、铝锰A、1
B、2#
C、3
D、4
- 采用小浮标测流时,每个浮标的运行历时一般应不少于(),如流速较大,可酌情缩短,但不能少于10s。钢尺起始零点对不准、尺子读数不准、测钎插不准、线锤对点等引起的误差都属于()。A、20s#
B、30s
C、50s
D、60sA、丈
- 电动机缺相时,会使离心泵()QHSE管理体系文件中提供如何完成活动和过程的信息文件是()。A、振动
B、产生水击
C、转不动#
D、发生汽蚀A、程序文件#
B、作业文件
C、记录
D、管理手册
- 当缺测期间的上下游站区间流量(),且两站的水位过程线又大致相似时,可参考临站的水位过程线补绘出本站的水位过程线,从而插补出本站的缺测水位。完全相等
差别大
为某固定值
变化不大#
- 浮子式水位计记录笔由石英晶体()以每小时一定的速度带动它在记录纸横坐标方向上单向运动。激光法泥沙颗粒分析一般使用湿样,静置后直接将浓度调整为既能充分混匀又易取样的()浆体,或经试验控制为以能满足最佳取样
- 渗出水流的颜色可用其()表示。均质堤防的浸润线,在起点与终点之间以()连接。纯净度
含沙量
浑浊度
透明度#直线
折线
圆弧线
平滑渐变的曲线#
- 为便于区别和比较分析,标绘()主流线时可选择不同的线型、颜色。不同时期的#
某次
某时
某段
- 可用作盖堵漏洞进口软帘的有()。蓬布#
复合土工膜#
土工织物#
土工编织布#
土工格栅