查看所有试题
- 砂浆回弹仪主要技术性能指标标称动能,下列那些不是正确的()0.190J#
1.96J#
0.196J
1.90J#
- 砂浆测强仪上刀片行程技术指标应符合()干混砂浆生产用砂水分应控制在()。>20mm
>200mm
>30mm#
>300mm≤0.5#
≤1.0
≤2.0
≤3.0
- 筒压法检测砖砌体中砌筑砂浆强度,水泥砂浆中所用砂的品种有()粗砂
中砂#
细砂#
特细砂#
- 集料具有如下()作用。骨架作用#
稳定体积变形作用#
改善砂浆耐久性#
影响砂浆的性能#
- 砂浆测强仪示值相对误差技术指标应符合().点荷法中,应将破坏后的试件拼接成原样,测量荷载实际作用点中心到试件破坏线边缘的最短距离,即荷载作用半径,不应精确至().±3%#
±30%
±4%
±40%1cm#
1mm#
0.1mm
0.01mm#
- 贯入法中,贯入深度测量表分度值应为()筒压法检测的测试设备所用的托盘天平要求称量为1000g、感量为().0.01mm#
1mm
0.1mm
10mm0.01g
0.1g#
1g
- 用贯入法检测时,砌筑砂浆龄期应满足为()27d
28d或28d以上#
7d
14d
- 筒压法检测的测点不应位于()干混普通防水砂浆的抗渗等级有()。墙体中部
门窗洞口处#
补砌的临时施工洞口附近#P6#
P8#
P10#
P4
- 筒压法检测砖砌体中砌筑砂浆强度,特细砂水泥砂浆筒压荷载值应为().砂浆测强仪测试荷载范围技术指标应符合()10kN#
15kN
20kN
25kN40N~1400N#
400N~1400N
400N~14000N
4N~140N
- 推出法中,推出仪的示值相对误差为()当砂浆拌合物稠度大于()mm时,宜采用人工插捣法。±2%
±3%#
±5%
±8%50#
60
70
80
- 纤维素醚主要有()功能。砂浆立方体试块可以放在()的标准养护室中养护。优良的保水性#
粘结力强、抗垂性好#
减水性能
溶解性好#温度22.5℃、湿度93%
温度20.5℃、湿度92%#
温度19.5℃、湿度92%#
温度20.5℃、湿度88%
- 贯入法中,每一个构件应测试()点.立方体抗压强度试验中,砂浆试块的养护条件:()12
14
16#
18温度20℃±5℃、相对湿度45%~75%
温度20℃±2℃、相对湿度60%~80%
温度20℃±2℃、相对湿度(60±5)%
温度为20℃±2℃,相对湿度为
- 筒压法检测砖砌体中砌筑砂浆强度,进行筒压荷载测试,制备试样时,每个试样应分两次装入筒压筒每次宜装1/2,应在水泥跳桌上跳振().气硬性胶凝材料包括有()。2次
3次
4次
5次#水泥
石膏#
粉煤灰
石灰#
- 下列不属于干混砌筑砂浆出厂检验项目的是()。保水率
2h稠度损失率
抗压强度
凝结时间#
- 采用砂浆片剪切法检测时,每个测点处,宜取出()砂浆片.将砂浆试件水平放置在下加荷头上时,上、下加荷头应()预先画好的作用点.一片
两片#
三片
四片偏移
对准#
平行
不平行
- 砂浆回弹法检测筑砂浆强度时,原位检测的水平灰缝应处于()浸水饱和状态
自然状态
干燥状态#
- 贯入力的校准中,弹簧拉压试验机应下压()干混砂浆中人工砂的总压碎值指标应小于()。10±0.12mm
20±0.12mm
10±0.10mm
20±0.10mm#10
20
30#
40
- 筒压法检测方法中,称量各筛筛余试样的重量时,各筛的分计筛余量和底盘剩余量的总和,与筛分前的试样重量相比,下列哪几组数据超过了标准规定的相对差值要求()水泥初凝时间当试针沉至底板()mm时为水泥初凝时间。0.5
- 砂浆成型方法应根据稠度而确定。当稠度()时,宜采用人工插捣成型。砂浆凝结时间测定中,两次试验结果的误差不应大于()min,否则应重新测定。大于50mm#
小于50mm
大于60mm
小于60mm5
10
20
30#