查看所有试题
- 产生吊钩游摆的原因是()。斜吊#
运行机构突然启动或制动#
物体或设备吊装不当#
- 对新投产的吊钩在使用时应作以额定载荷()倍的负荷实验,卸载后,钩口开度变形不应超过0.25%,否则应报废。引起钢丝绳破坏的主要原因是()。1
1.25#
1.5
2斜拉、斜吊
反复弯曲所造成钢丝绳疲劳和磨损#
吊物摆动
重物
- 起吊货物时,操作员应确知所吊载荷重量,所吊载荷的重量不得超过()。吊机的最大载荷
吊机所处工作半径的安全载荷#
吊机所处工作半径的正常载荷
- 卷扬机无论在什么条件下工作,留在卷筒上钢丝绳不少于()圈。当钢丝绳发生()时,将会导致钢丝绳的实际直径比名义直径小。1
2
3#
4外部磨损#
绳芯断裂#
内部腐蚀#
外部腐蚀#
- 在下列操作中,信号员采用基本手势进行指挥的有()。升钩#
升吊臂#
保持不动#
降吊臂并升钩
紧急停止#
旋转加降钩
- ()钢丝绳在起重机中应用较多。同向捻
交互捻#
混和捻
- 在任何情况下,滚筒上必须至少保留有()圈以上的钢丝绳。3
4
5#
6
- 当安全系数为6时,钢丝绳报废标准规定,交互捻钢丝绳在一个捻距内断丝数为钢丝总数的()时,就应报废。司机在闭合主电源前或起重机在工作时突然断电,都应将控制器手柄置于()。3%
5%#
7%
10%起升位置
下降位置
零
- 对新投产的吊钩在使用时应作以额定载荷()倍的负荷实验,卸载后,钩口开度变形不应超过0.25%,否则应报废。1
1.25#
1.5
2
- 起重机的工作类型是指起重机工作忙闲程度和载荷变化的参数,它分为()。轻、中、重三个级别
轻、重、特重三个级别
轻、中、重、特重四个级别#
- 当安全系数为6时,钢丝绳报废标准规定:同向捻钢丝绳在一个捻距内断丝数为钢丝总数的()时,就应报废。根据工作状态,吊机制动器分为()。3%
5%
7%
10%#常开式#
常闭式#
自动作用式
操纵式
- 不得在有载荷的情况下,调整()的制动装置。起升设备
变幅机构#
起升机构和变幅机构
- 对新投产的吊钩在使用时应作以额定载荷()倍的负荷实验,卸载后,钩口开度变形不应超过0.25%,否则应报废。1
1.25#
1.5
2
- 主副钩和吊臂使用的钢丝绳有下列()情况时必须更换。六根断丝随机分布在一圈距内#
三根断丝随机分布在一圈距内
一股中有两根断丝在同一圈距内#
一股中有一根断丝在同一圈距内
- 卷扬机无论在什么条件下工作,留在卷筒上钢丝绳不少于()圈。司机在闭合主电源前或起重机在工作时突然断电,都应将控制器手柄置于()。1
2
3#
4起升位置
下降位置
零位#