查看所有试题
- 过卷扬限制器〔又称上升极限位置限制器)的功用是当吊钩升到上限极限位置时,它开始动作,切断电源.以确保安全。()在紧急情况下,能切断起重机总控制电源的装置是()。运行极限位置限制器由什么与行程开关组成:()
- 缓冲器应具有吸收运动机构的能量并增加冲击的性能;()符合制动器报废标准的有:()起重机车轮按其踏面形状分为:()起重机卷筒上出现裂纹可继续使用:()起重机械中的钢丝绳应视为一种不易损件。()A、正确
B
- 起重机上的车轮支承装置大体分为:()制动器的()疲劳、材料老化或产生裂纹、无弹力,将导致制动力矩减小。制动器的()磨损严重.制动时铆钉与制动轮接触,不仅降低制动力矩而且划伤制动轮表面,应及时更换。制动行程
- 过卷扬限制器〔又称上升极限位置限制器)的功用是当吊钩升到上限极限位置时,它开始动作,切断电源.以确保安全。()起重机额定起重量仅指起重机正常作业时允许起吊的最大重量。()在紧急情况下,能切断起重机总控制电
- 常闭式制动器在不通电时制动器是()的。起重机的起升高度是指()。起重机械用滑轮制造方式为():为保证电磁铁对衔铁有足够的吸力,应调整:()制动器打不开的原因是:()A、打开
B、闭合#
C、不确定A、臂端部距
- 对制动器的要求有()起重机的起升机构、变幅机构的制动器,必须是()制动器:制动器的()疲劳、材料老化或产生裂纹、无弹力,将导致制动力矩减小。制动器刹车不灵,应清除磨擦衬带油污及调整制动间隙,更换弹簧。()
- 采用无轮缘的车轮,在其两侧不应装水平轮。()起重机起升机构的制动器必须能可靠地制动住1.1倍的载荷;()为防止起重机被大风吹动或刮倒而安装的安全装置是()制动块摩擦衬垫磨损量达原衬垫厚度的()%,应报废。运
- 经常处于合闸状态,当机构工作时利用外力的作用使之松闸,这种制动器称为:()起重机的核心机构是起重机的操作机构。()为了使制动器松闸时,左右制动瓦块与制动轮之问的间隙对称,应调整:()运行极限位置限制器由安
- 空载检查起升机构高度限制器好坏时,将吊钩升到规定的高度后,如能停止,说明高度限制器是好的,如能不能停止说明高度限制器是坏的。()起重机的核心机构是起重机的操作机构。()起重机制动器的摩擦片与制动轮的接触面
- 常闭式制动器在不通电时制动器是()的。缓冲器是一种()装置。压板螺栓应有防松装置。()制动轮直径磨损到比原直径小()时,应重新加工恢复原来的表面硬度才能使用。制动轮发热.摩擦片很快磨损并烧焦的原因有()
- 当载荷达到额定起重量的90%时,超载限制器应能发出()报警信号。起重机额定起重量仅指起重机正常作业时允许起吊的最大重量。()上升极限位置限制器的作用是:()起升高度是指起重机吊具最高和最低工作位置之间的垂
- 超载限制器的广泛使用能有效的防止()情况而引起的断绳事故。超负荷限制器是在起重机起升时超负荷起保护作用,这时起重机会()。缓冲器应具有吸收运动机构的能量并增加冲击的性能;()数字载荷控制仪超载保护;当
- 超载限制器的广泛使用能有效的防止()情况而引起的断绳事故。采用无轮缘的车轮,在其两侧不应装水平轮。()规范要求,上升极限位置限制器必须保证当吊具起升到极限位置,能自动切断起升的动力源。()起重机的核心机
- 过卷扬限制器〔又称上升极限位置限制器)的功用是当吊钩升到上限极限位置时,它开始动作,切断电源.以确保安全。()起重机上外露的、有伤人可能的转动零件,如开式齿轮、联轴器、传动轴、链轮、链条、传动带、皮带轮等
- 不装上升极限位置限制器的危害是卷筒可能过卷扬拉断钢丝绳,吊钩下坠能造成人身伤亡。()起升机构、变幅机构的制动轮,轮缘厚度磨损达原厚度的()时,应报废。起重机上常用卷筒表面通常切出螺旋槽是为了:()上升极
- 当吊钩的起升高度达到规定值时()切断电源起保护作用。起升机构、变幅机构的制动轮,轮缘厚度磨损达原厚度的()时,应报废。起重机的工作幅度为()。起重机要经常检查紧急停止开关的停机效果。()起重机工作级别是