查看所有试题
- 锯割软性材料时锯条的往复速度要慢些,锯割硬性材料时速度要快些。()汽轮机油循环倍率多少最为合适?()使用斜背扒杆或起重机起重时,其斜背与水平面所夹的角度应在()之间。正确#
错误3~7
8~10#
10~1520°~50°
- 不合格品的处置方式是()。已知工质的压力p和温度t,在该压力下,当t低于饱和温度时,工质所处的状态是()。一根长度为L、电阻为R的导线,将其对折时,则电阻为()。返工
返修或不经返修让步接受
拒收、报废、更换
A、
- 用来夹持工件,其规格以钳口的宽度表示,有()mm等。在电力系统中,连接在电力网中各发电机组的功率总和称为()。汽包炉中,汽水分离是在()中完成的。30Hz
50Hz#
40Hz
60Hz10,50,80,90
100,125,150#发电负荷#
用电负
- 目前油管道连接法兰的垫料多采用隔电纸垫和橡胶垫。()正确#
错误
- 同步器的低限位是为使机组在()。高参数、高真空及低频率下能并网#
低参数、高真空及低频率下能并网
低参数、低真空及高频率下能带上额定负荷
高参数、低真空及高频率下能带上额定负荷
- 在解体调速系统各部件中,松螺母时要先看好是反牙还是正牙,不可盲目用力猛打。()各部件组装完毕,如暂时不与系统相连接时,需对各孔洞作临时封闭。对空气孔应用()封闭。正确#
错误铁皮堵板加衬垫
白布绑扎牢固
橡皮
- 钻头的后角大,切削刃虽然锋利了,但钻削时易产生排屑困难。()通常情况下,流体自由流动换热系数比强迫流动换热系数()。正确#
错误大
小#
相同
换热系数与流动性能无关
- 薄膜钢带式调压器组装后应对薄膜室进行水压试验。一般试验压力为最高工作压力的1.1~1.25倍,保持5min不泄漏即符合密封要求。()轴承的进油口位置应选择在油膜中压力()的地方。正确#
错误>0
<0
=0#
- 某台机组同步器的工作范围在+4%~-3%。调整是否恰当()。透平油的酸价应不大于()毫克KOH/克油。太大
太小#
合适
不确定3.0
2.0
1.0#
- 在紧油管法兰螺丝时,要先将螺帽戴平,然后对角紧好,用力要均匀适度。()正确#
错误
- 各部件组装完毕,对暂不与系统相连接的法兰应用白布绑扎牢固。()正确#
错误
- 对实体的一个或几个特性进行的诸如测量、检查、试验或度量并将结果与规定要求进行比较以确定每项特性合格所进行的活动,称为()。汽轮机调速系统温度较高部件如滚动轴承、门杆、活动铰链等应涂以()。检验#
验证
过
- 汽轮机调速系统的迟缓率一般不应超过0.6%。()公称压力为25的伐门属于()伐门。正确#
错误高压
中压#
低压
- 调速部套装配时,滑动及转动部分应灵活、无卡涩与松动现象,全行程动作应灵活、准确。()正确#
错误
- 气焊火焰的碳化焰适于焊接一般碳钢和有色金属。()台钳的高度一般以()为宜。正确#
错误800~900mm#
1000mm
500mm
1100mm
- 由组织的最高管理者正式发布的该组织总的质量宗旨和质量方向,称为质量计划。()正确#
错误
- 发电厂的转动设备和电气元件着火时,不准使用CO2灭火器和砂土灭火。()使用斜背扒杆或起重机起重时,其斜背与水平面所夹的角度应在()之间。对实体具备满足规定要求能力的程度所做的有系统的检查,称为()。油管路连
- 可燃物的爆炸极限越大,发生爆炸的机会越多,危险性越大。()()主油泵在启动前必须要灌油。正确#
错误螺旋式
齿输式
离心式#
- 在起吊不规则物体的拆装或就位时,需要用手拉葫芦(倒链)或花篮螺丝来调节一端钢丝绳的长度。()机组带额定负荷时,()会使机组出力不足。正确#
错误电网频率升高#
电网频率下降
主蒸汽参数变化
- 中联门主汽门阀碟磨损后,关闭的富裕行程消失时可能引起安全油压的降低。()双侧进油主油泵的推力间隙不宜太大,一般应在()范围内。正确#
错误0.08~0.12mm#
0.15~0.20mm
0.20~0.40mm
0.50~1.00mm
- 握錾方法因工作性质不同有三种:正握法、反握法、横握法。()机组带额定负荷时,()会使机组出力不足。正确#
错误电网频率升高#
电网频率下降
主蒸汽参数变化
- ISO9002质量体系是设计、开发和试验的质量体系。()采用给水回热是减小()的有效办法。正确#
错误冷源损失#
抽汽损失
汽耗率
热效率
- 企业推行ISO9000系列标准有利于提高市场竞争力。()正确#
错误
- 中联门安全油压不能建立,则说明中联门托盘的阀线不严密或已损坏。()正确#
错误
- 高压油系统可以使用铸铁或铸铜阀门。()质量方针是由()颁布该组织总的质量宗旨和质量方向。油管路连接法兰剪垫时,要求垫的内径应大于管内径()mm,以防垫的位置不对中心时遮住油管内径。正确#
错误总工程师
副总
- 放大器一次油压p1与二次油压p2变化方向相反的目的是防止因漏油等因素使二次油压?p2下降时误将调节阀开大。()针对特定的产品、项目或合同,规定专门的质量措施、资源和活动顺序的文件,称为()。正确#
错误质量评价
- 主油泵的窜动太大会引起速闭器产生误动作。()测量Φ30~50mm滑阀的间隙可用:()。公称压力为25的伐门属于()伐门。旋转阻尼或径向泵调速器在组装扣盖时,应在水平结合面上紧上1/3螺栓,然后用()mm塞尺不通,则严
- 当真空下降,负荷不变时,机组元件的(压)应力可能超过允许值,推力轴承也可能过载。()在火力发电厂的能量转换中,热能向机械能的转换是在()中完成的。正确#
错误锅炉
汽轮机#
发电机
变压器
- 返修是指对不合格产品所采取的措施,使其满足规定的要求。()汽轮机转子的弯曲度应为:()。浓酸强碱一旦溅入眼睛或皮肤上,首先应采取()方法进行抢救。企业实施ISO9000系列标准的目的是()。正确#
错误≤0.04mm#
- 磁偏吹产生的原因主要是因为电焊条药皮偏心引起的电弧偏移。()正确#
错误
- 采用高压调节阀动态过调能改善再热机组的功率延滞现象。()电容C1、C2、C3串联后的等效电容量C为()。工质达到临界状态在喷管中流动,在缩放喷管的渐扩部分()。正确#
错误C=C1+C2+C3
C=1/C1+1/C2+1/C3
1
- 油系统阀门不允许竖装,以防阀芯脱落造成断油。()通常情况下,流体自由流动换热系数比强迫流动换热系数()。正确#
错误大
小#
相同
换热系数与流动性能无关
- 主汽门活动试验是保证主汽门油动机动作灵活的手段之一。()锉削的表面不可用手擦摸,以免锉刀()。原始平板刮削法,应该采用()板互相研制。正确#
错误打滑#
生锈
破坏加工表面两块
三块#
四块
五块
- 凝汽式汽轮机的轴封系统是为了防止蒸汽漏出,造成工质损失,恶化运行环境等。()研磨时,表面出现拉毛,其原因是()。正确#
错误磨料太粗
工件发热超过50℃
研磨剂太薄
清洁工作没做好#
- 溢油阀装在冷油器进口油路管道上,其作用是保持润滑油压稳定。()调节系统的静态特性曲线是由()决定的。油系统中的直流油泵的作用是()。正确#
错误机组油压变化曲线
机组所带负荷的曲线
机组转速曲线
调速器特性
- 主汽门活动试验不动,说明门杆已卡涩()正确#
错误
- 迟缓率的存在延长了自外界负荷变化到汽轮机调节阀开启动作的时间间隔。()正确#
错误
- 兆欧表是测量电压和电流的仪表。()旋转阻尼或径向泵调速器在组装扣盖时,应在水平结合面上紧上1/3螺栓,然后用()mm塞尺不通,则严密性合格。正确#
错误0.02
0.05#
0.08
0.10
- 同样型号的汽轮机,它们的调速系统特性是一样的。()调速汽门油动机滑阀开汽门方向的行程比关汽门方向行程()。同步器上限偏低会造成()。正确#
错误大
小#
一样带不满负荷#
不能减负荷到零
甩负荷时超速
系统不稳
- 吊物用的三角架,每根支腿与地面水平的夹角不应小于50°。()工质在流动过程中它的分子在不断的热运动,工质所具有克服分子间吸引力的能量叫工质的()。水在水泵中被压缩升压可以看作是()。在冷态条件下,危急遮断器