查看所有试题
- 在对轴承合金脱胎处进行补焊时,必须严格控制施焊处瓦胎温度不得超过()℃。检修转子弯曲度时应使用()来进行测量、20
50
10#
0D.200A、百分表#
B、内外径千分尺
C、游标卡尺
- 干饱和蒸汽的干度等于()。若各层保温材料表面温度保持不变,则通过每一层的热量是()的。0
0.5
1#可变化的
不等的
相等的#
- 汽轮机在额定转速工作其振动()。动静叶间隙的测定使用的工具是()利用轴向埋入法安装的叶片的叶根型式是()>=0.05mm
<=0.05mm#
<=0.15mmA、塞尺
B、楔形塞尺#
C、百分表A、T型叶根
B、菌型叶根
C、枞树
- 一般导热性能好的物质导电能力()。汽轮机转子停止后应立即投盘车运行()小时。凝结器真空降低,排汽温度与凝结器端差的变化趋势是()不好
也好#
差1
2
3
2-4#A、排汽温度升高,端差降低;
B、排汽温度降低,端差降
- 大气式除氧气的工作压力为()表压。1.2at
0.02MPa#
0.12MPa
- 动静叶间隙的测定使用的工具是()泵轴过热的原因()。A、塞尺
B、楔形塞尺#
C、百分表 泵轴与电机轴同心
润滑油脂过多#
轴承位移间隙过大
轴承损坏
- 一般在临界转速时,轴承的双倍振幅值不应超过()mm。A、0.02
B、0.03
C、0.10#
- 高压转子一般采用()直轴汽轮机运行中,当发现凝结水泵流量增加、电流增大、负荷没变、真空有所增加时,应判断为(),并通过化验水质合格。A、内应力松弛法#
B、局部加热法
C、机械加压法A、低压加铜管漏泄;
B、备用
- 物体间不接触而进行热交换的方式为()。利用轴向埋入法安装的叶片的叶根型式是()对流传热
辐射传热#
热传导A、T型叶根
B、菌型叶根
C、枞树型叶根#
- 在潮湿或周围均属导体的容器中工作时,行灯电压不得超过()A、36
B、24
C、12#
- 位于给水泵和锅炉省煤器之间的加热器为()。滑压运行除氧器当负荷突增时,给水含氧量变化是()。当汽机的通流部分结垢时,袖向推力()低压加热器
除氧器
高压加热器#
汽封加热器A、减少;
B、增大;#
C、不变。A、
- 对于运行中的换热设备,强化或削弱传热的方法只能从()要素入手高压加热器运行中,水侧压力()汽侧压力,为保证汽轮机组安全运行,在高加水侧设有自动旁路保护装置。A、传热面积
B、热、冷流体的温差
C、传热系数#A、
- 在起吊大盖时人员不可少于()人,但必须由一个人统一指挥。A、4
B、6
C、8#
- 位于给水泵和锅炉省煤器之间的加热器为()。汽轮机凝汽器真空变化将引起凝汽器端差变化,一般情况下,当凝汽器真空升高时,端差()。低压加热器
除氧器
高压加热器#
汽封加热器A、增大
B、不变
C、减小#
D、先增大后
- 调节、保安油系统油管试漏时启动()。一般在临界转速时,轴承的双倍振幅值不应超过()mm。高压电动油泵#
低压电动油泵A、0.02
B、0.03
C、0.10#
- 汽轮机长期低负荷运行,会加速()叶片水蚀的发展。工质在状态变化过程中不与外界进行热量交换的过程即()。末几级#
中间级
调节级
所有级等容过程
绝热过程#
等压过程
- 低比转速的泵一般用于()。A、流量大,扬程低的场合;
B、流量小,扬程高的场合;#
C、流量小,扬程低的场合。