查看所有试题
- 电能表的转盘转矩是由()电杆倾斜度不应大于杆长的()。低压接户线至通车道路中心的垂直距离不得小于()mm。某配电室一条分路出线断路器检修,同时该分路线路上也进行检修,数字4代表()用管螺纹板套丝,与接线盒、
- 供电所()应每月安排1~2天定期接待客户。熔断器式刀开关适用于交流50HZ、380V或440V,负荷电流100~600A的配电网中,作为电器设备的()保护。变压器同相原绕组的1匝导线与副绕组的1匝导线所感应的电势()。电气施工
- 在混凝土上打16mm以上孔径的洞,应用()。用于1kV及以下的绝缘垫的厚度应不小于()mm。铝芯聚氯乙烯绝缘导线的型号是()。DG型导电膏涂敷于导电排搭接处和电气设备连接处,可以降低接触电阻()%。对于450拉线长度
- 低压安规DL477-2001规定:在工作期间,工作票应始终保留在工作负责人手中,工作终结后应交供电所保存,时间为()。容量小于()的交流接触器,一般采用的灭弧方法是双断口触头和电动力灭弧。跌落式熔断器主要用于架空配
- DD862型单相电能表的准确度等级一般是()。造成配电变压器低压侧熔丝熔断的原因可能是()。三个驱动元件的电能表用于()供电系统测量和记录电能。防止电气火灾漏电保护装置的动作电流数值选择为()Ma。住宅配电
- 操作柱上断路器时,应注意()防止伤人。高压验电器绝缘部分长度,对10kV及以下的不小于()m。测量500~1000V电气设备或回路的绝缘电阻时,应采用()V兆欧表。感应式电能表可用于()。瓷瓶配线线路导线必须用绑线牢固
- 继电器是组成继电保护装备的基本元件,当输入量超过或低于一定值时它就动作,并通过()发出信号或动作于跳闸。配电线路的相序排列,按A.B.C顺序,用()颜色表示。对升降板进行检验,试验时将其系于水泥杆上,离地()m左
- 三极管内部由三层半导体材料组成,分别称为发射区、基区和集电区,结合处形成两个PN结,分别为发射结和()。配电线路要做到有序管理,必须对线路和设备进行()。绑扎导线用铜绑线的直径应在()mm范围内,使用前应做退
- 在PN节之间加(),多数载流子的扩散增强,有电流通过PN节,就形成了PN节导电。配电线路的相序排列,按A.B.C顺序,用()颜色表示。正弦交流电的幅值就是()。柱上断路器是一种担负()任务的开关设备。异步电动机的()
- 当三极管集电极与发射极之间的电压UCE为一定值时,基极与发射极间的电压UBE与基极电流IB之间的关系,称为三极管的()。电气施工图中的()最为重要,是电气线路安装工程主要图纸。操作柱上断路器时,应注意()防止伤人
- 在PN节之间加(),多数载流子扩散被抑制,反向电流几乎为零,就形成了PN节截止。分支杆也是分支线路的()。低压接户线最大风偏时与烟囱、拉线、电杆距离不得小于()mm。兆欧表应根据被测电气设备的()来选择电气施
- 表示金属材料的坚硬程度叫金属的()。槽板配线适合于导线截面在()mm2以下的室内照明线路我国的船舶空调舱室设计标准是夏季室温()。A、硬度#
B、强度
C、力度
D、温度A、2.5
B、4#
C、6
D、1018-20度
19-22度
- 三极管共发射极接法电路,集电极电流的变化量ΔIC与基极电流变化量ΔIB的比值称为三极管共发射极接法()。绝缘夹钳只允许使用在额定电压为()kV及以下的设备上。接触器的辅助触头,通常由()对及以上的常开常闭辅助触
- P型半导体空穴数远多于自由电子数,这些空穴是多数载流子,而自由电子是少数载流子,导电能力主要靠空穴,称为空穴型半导体,简称()。当参考点改变时,电路中两点之间的电位差是()。双人抢救触电者时,每按压()次后再
- 对反映短路故障的继电保护装置的四个基本要求是()。当参考点改变时,电路中两点之间的电位差是()。参考点也叫零电位点,它是由()的。铝芯聚氯乙烯绝缘导线的型号是()。悬式绝缘子的表示符号为()。在绑扎铝导
- 在半导体中掺人微量的有用杂质,制成掺杂半导体。掺杂半导体有()。参考点也叫零电位点,它是由()的。低压接户线一般两悬挂点的间距不大于()m,若超过就应加装接户杆。封闭式负荷开关操作机构有(),避免发生触电
- 用一个恒定电流Is和一个电导GO并联表示一个电源,这种方式表示的电源称电流源。若GO=0则称为()。拉线棒通常采用直径不小于()圆钢制做。异步电动机的型号为Y355M2-4,数字4代表()瓷夹板(瓷卡)敷设适合于导线截
- 这些自由电子是多数载流子,而空穴是少数载流子,导电能力主要靠自由电子,称为电子型半导体,应检查锤把、锤头及钢钎,打锤人应站在扶钎人()。电气工程在工程开工前,要根据施工图纸制定()计划。双层绕组主要用于容量
- 我国的船舶空调舱室设计标准是夏季室温()。分支杆也是分支线路的()。测量绝缘电阻使用的仪表是().绝缘带包缠时,用黄蜡带从导线左边完整的绝缘层上开始包缠,包缠()带宽后就可以进入连接处的芯线部分。在编插
- 将P型半导体和N型半导体经过特殊工艺加工后,会有机地结合在一起,就在交界外形成了电荷的薄层,这个带电荷的薄层称为()。锥型电杆的锥度为()。编插钢丝绳套时,为了防止每股钢丝绳松散,应用()将各股钢丝绳头缠绕
- 当三极管基极电流为某一定值时,集电极电压UCE与集电极电流IC之间的关系曲线为三极管的()。高压验电器绝缘部分长度,对10kV及以下的不小于()m。安装剩余电流动作保护器的低压电网,其正常漏电电流不应大于保护器剩
- 涡流是一种()现象DG型导电膏涂敷于导电排搭接处和电气设备连接处,可以降低接触电阻()%。在电能表型号中,表示电能表的类别代号是()。当柱上电力电容器容量在30Kvar及以下时,熔丝元件按电力电容器额定电流的()
- 公制普通螺纹的牙型角为()。高压验电器绝缘部分长度,对10kV及以下的不小于()m。分支杆也是分支线路的()。线路名称及编号若采用悬挂标志牌,悬挂高度应距地面()左右。铁横担锈蚀面积不宜超过截面的(),否则应
- 起重用的钢丝绳的静力试验荷重为工作荷重的()倍。分支杆也是分支线路的()。接触器的辅助触头,通常由()对及以上的常开常闭辅助触头构成。测量绝缘电阻使用的仪表是().架空低压配电线路的导线在绝缘子上的固定
- 起重用的钢丝绳的安全系数为()DX型是()电能表.绑扎导线用铜绑线的直径应在()mm范围内,使用前应做退火处理。在锅炉等金属容器内工作场所用的行灯采用的电压是()V。建筑施工工地的用电设备漏电保护装置的动作
- 电阻、电感、电容串联的交流电路中,当电路中的总电流带后于电路两端电压的时候()。配电线路要做到有序管理,必须对线路和设备进行()。一般测量100V及以下低压电气设备或回路的绝缘电阻时,应使用()V电压等级的兆
- 电阻、电感、电容串联的交流电路中,电路中的总电流与电路两端电压的关系是()。磁电系仪表只能用于()。电流互感器二次回路所接仪表或继电器线圈,其阻抗必须()。配电变压器容量不大于100kVA时,接地电阻可不大于
- 起吊钓钩在使用时,一定要按规定使用,不能()。分支杆也是分支线路的()。涡流是一种()现象A、欠负荷
B、超负荷#
C、超80%负荷
D、超70%负荷终端杆#
转角杆
直线杆
跨越杆电磁感应#
电热流效应
化学效应
流化学效
- 用一个恒定电动势E和一个内阻R0=0时我们称之为()。一般情况下拉线与电杆的夹角不应小于()度。开启式负荷刀开关的安装方向应为合闸时手柄(),不准倒装或平装。测量变压器铁心对地的绝缘电阻,应先拆开()。横担
- 用一个恒定电流Is和一个电导GO并联表示一个电源,这种方式表示的电源称()。铝芯聚氯乙烯绝缘导线的型号是()。电磁系仪表可用于()。铜的比重比铝()。封闭式负荷开关俗称()。编插钢丝绳套时,为了防止每股钢丝
- D表示单相,S表示三相三线,()表示无功,B表示标准.电动机铭牌上的接法标注为380V/220V,Y/△,当电源线电压为380V时,电动机就接成()。高压设备独立的接地装置,接地电阻值不应大于()Ω。在工程开工前,及时向施工小组
- 交流电焊机的绝缘电阻低于()MΩ时,应进行干燥处理。测量接触器相间绝缘电阻,绝缘电阻值不应低于()MΩ。斜削法需先用电工刀以()角倾斜切入绝缘层,当切近芯线时,即停止用力。测量1000~3000V电气设备或回路的绝缘电
- 电阻、电感、电容并联的交流电路中,当电路中的总电流滞后于电路两端电压的时候()。铁道、航运等信号灯用电应按()电价计费。一般工作场所移动照明用的行灯采用的电压是()V。电动机铭牌上的接法标注为380V,△,当
- 亚弧焊时,要保持电弧()。用电工刀剖削导线时,应以()角倾斜切入塑料绝缘层,应使刀口刚好削透绝缘层而不伤及芯线。钢管配线时钢管弯曲处的弯曲半径,不得小于该管直径的()倍。抄表是()工作的第一道工序,直接涉
- 电阻、电感、电容并联的交流电路中,电路中的总电流与电路两端电压的关系是()。悬式绝缘子的表示符号为()。使用外线用压接铅每压一个坑,要持续压力()min再送开.在编插钢丝绳套时,除了要按规定的尺寸要求外,各
- 户外落地变压器油量在()kg及以上时,应设置能容纳全部油量的设施。高压验电器绝缘部分长度,对10kV及以下的不小于()m。一电感线圈接到f=50Hz交流电路中,感抗XL=50Ω,若改接到f=150Hz的电源时,则感抗XL为()Ω。A、4
- 户外落地变压器外廓与建筑物外墙距离小于()M时,应考虑对建筑物的防火要求。A级绝缘材料最高允许工作温度为()0C。瓷鼓配线适合于导线截面在()mm2以下的室内照明线路。电动机铭牌上的接法标注为380/220V,Y/△,当
- 户外落地变压器底座的底面与地面距离不应小于()m。目前常用的裸导线型号为()两大类。跌落式熔断器的额定电流必须()熔丝元件的额定电流。大工业用户的受电变压器容量在()。配电箱暗装时底口距地面为()m。为
- 容量在()KW及以上的电动机需装设失压(零压)和欠压(低电压)保护。对于450拉线长度可按地面杆高的()倍来计算,并加上回头缠绕长度。一台配电变压器的型号为S9—630/10,该变压器的额定容量为()。重量大于300kg
- 户外落地变压器台周围应安装固定围栏,围栏高度不低于()M安全带试验周期为()试验一次。容量小于()的交流接触器,一般采用的灭弧方法是双断口触头和电动力灭弧。某配电室一条分路出线断路器检修,同时该分路线路上