查看所有试题
- 视线运动的顺序习惯于从()进行。安全带要(),注意防止摆碰撞。MQ2533门机变幅机构设有()级限位保护开关。根据时间继电器触点的延时通断情况,它的延时触点共有()种形式。低副是指两构件之间为()接触的运动副
- 极限力矩联轴节摩擦面之间需保持足够的接触表面,锥形摩擦盘内外锥面接触面积不小于()。将机器上的紧急事故开关(亦称急停开关)作为一般操作的停止开关频繁使用,这是()的。港口机械的完好率是指机械的()台时占
- 制动轮表面温度不得超过()°C。安全带是进行机械高处作业人员预防坠落伤亡的个体防护用品,安全带的正确使用方法是()。减速器在正常运行时期箱体,特别是在安装轴承处不能过热,一般减速箱内油温不应超过()℃。门机
- 安全带是进行机械高处作业人员预防坠落伤亡的个体防护用品,安全带的正确使用方法是()。空载状态又称为断路或者开路状态,电路空载时,外电路电阻可视为()。优质碳素钢的含硫量小于或等于()%。断面收缩率是金材料
- 极限力矩联轴节摩擦面之间需保持足够的接触表面,锥形摩擦盘内外锥面接触面积不小于()。起重机的工作参数有:起重量、幅度、起升高度、各机构的工作速度、()及生产率。门机起升变速齿轮箱转换速度时,转换只能在(
- 检查齿条心轴缓冲行程,缓冲行程不得大于原行程的()。ZG200-400的抗拉强度为()Mpa。以下不属于润滑油质量指标的是()。触电事故中,绝大部分都是导致人身()伤亡的。受压杆件钢板每米长度内波浪度应不大于()mm
- 极限力矩限制器打滑不大于()圈。为了保证足够的驱动力,起重机应当具有足够数目的驱动轮(主动轮),通常约为总轮数的()。为平衡重力负载,使运动部件不会因自重而自行下落,在恒重力负载情况下,采用内控外泄式顺序
- 柱式回转支撑门机的水平轮单边径向磨损不得大于()mm。由于()支承装置具有结构简单、制造方便、精度要求不高等优点,因此被广泛地应用于门座起重机。常用的精度为0.1mm、0.05m、0.02mm游标卡尺的尺身刻度是()的
- 在各类磨损中,以()最多。一块钢板,长5m,厚度为10mm,该钢板的重量为(),钢的密度为7.85t/m3。下列液压马达中,()为低速马达。下列不属于起重机计算载荷中的基本载荷的是()。当S﹥1时,电动机处于()状态。双伸
- 极限力矩联轴节摩擦面之间用弹簧压紧,弹簧压紧所产生的摩擦力矩为起动力矩的(),这个摩擦力矩作为制动力矩的极限。中心受电器的滑环和碳刷导电部分均应保持清洁,滑环与碳刷之间的接触面积不得少于碳刷面积的()%。
- 起升机构起升速度误差不大于()%。MQ2533门机变幅机构设有()级限位保护开关。材料20Mn2中,Mn的质量分数为()之2。下面常用低压电器件()不能作为短路保护来用。以下不属于润滑油质量指标的是()。以下()的抗
- 极限力矩联轴节摩擦面之间用弹簧压紧,弹簧压紧所产生的摩擦力矩为起动力矩的(),这个摩擦力矩作为制动力矩的极限。变幅系统在工作中,因臂架和货物的重心升降,将()变幅驱动功率。吊钩因扭转变形使钩身的扭转角口超
- 门机起升变速齿轮箱转换速度时,转换只能在()的条件下进行。起重机旋转部分重量以及货物重量引起的垂直力,由下支承的()来承受。MQ2533门机大风报警设定为()M/S左右。电磁式制动器工作时,电磁吸铁不应发出噪音,
- 三相异步电动机铭牌上标明:“额定电压380/220V,接法丫/△”。当电网电压为380V时,这台三相异步电动机应采用()。选用润滑时,所选润滑脂的滴点必须高过工作温度()℃。某电动机的转速为1475r/min,则该电动机的磁极数(
- 门机静负荷试验是将额定起升重量的()%的重块,起吊离地面100mm左右,悬空10分钟,没有下滑现象。以下()不是带传动的特点。某电动机的转速为1475r/min,则该电动机的磁极数()。低碳钢的含碳量小于或等于()%。MQ25
- 某电动机的转速为1475r/min,则该电动机的磁极数()。以下()#锂基润滑脂的针入度最大。在专业技术人员创新能力的结构体系中,创新能力产生的前提条件是()变频器电阻器的绝缘电阻应不低于()MΩ。以下关于磁场叙述
- 门座起重机可分为()组合臂架式门座起重机和单臂架式门座起重机两种。变幅系统在工作中,因臂架和货物的重心升降,将()变幅驱动功率。MQ2533门机变幅机构设有()级限位保护开关。以下种类轴承承受径向力最小的是(
- MQ2533门机变幅机构设有()级限位保护开关。港口机械的使用率是指机械的()台时占日历台时的百分比。在各类磨损中,以()最多。钙基润滑脂的适用工作温度为()。欲在两轴相距较远,工作条件恶劣的环境下传递较大功
- 门座起重机可分为()组合臂架式门座起重机和单臂架式门座起重机两种。我国标准规定标准直齿齿轮齿型角为()度。下面常用低压电器件()不能作为短路保护来用。门机行走轮踏面磨损量应不超原厚度的()%。从受力情
- 易燃液体应盛装在()内。在基孔制中,轴的基本偏差在a-h之间的属于()配合。钢丝绳绳尾固定用编接连接时,编接长度应不小于钢丝绳直径的15倍,并且不得小于()mm。起重机的工作参数有:起重量、幅度、起升高度、各机
- 下面能全面反映零件尺寸的视图是()。低碳钢的含碳量小于或等于()%。淬火的其目的主要是为了提高钢的硬度、强度和()。在吊运过程中,被吊物体应高于地面设备或其他物体()以上。下面不属于钢结构常见的破坏形式