查看所有试题
- 桥式RC振荡电路是用来产生一定频率和幅度的()。正弦交流信号#
正、负尖脉冲信号
方波信号
非周期信号
- 图11-42所示整流电路的输出电压Uo为()U21。要求输入电阻为100kΩ~200kΩ,电压放大倍数数值大于100,第一级应采用(),第二级应采用共射电路。0.45#
0.90
1.10
1.25共射电路
共集电路#
共基电路
共源电路
- LC振荡电路如图11-31所示,振荡频率为()。f0≈1/2π#
f0≈1/π
f0≈1/
f0≈2π
- 电路如下图所示,R1、R2支路引入的反馈为()。串联电压负反馈
正反馈#
并联电压负反馈
- 双极晶体管放大电路共射极接法所对应的场效应管放大电路是()接法。当有用信号的频率介于2500Hz与3000Hz之间时,应采用的最佳滤波电路是()。共基极
共源极#
共漏极
共栅极低通
高通
带通#
带阻
- 电路如图11-29所示,R1=10kΩ,R2=20kΩ,R=100kΩ,uI1=0.2V,UI2=-0.5V,则输出电压Uo为()V。要求输入电阻为100kΩ~200kΩ,电压放大倍数数值大于100,第一级应采用(),第二级应采用共射电路。-0.5
0.5#
1
-1共射电路
共
- 如图所示的放大电路()。直流电源滤波的主要目的是()。不能稳定静态工作点
能稳定静态工作点,但比无二极管D的电路效果要差
能稳定静态工作点且效果比无二极管D的电路更好#将交流变直流
将高频变低频
将正弦波变成
- 当有用信号的频率介于2500Hz与3000Hz之间时,应采用的最佳滤波电路是()。低通
高通
带通#
带阻
- 电路如图11-7所示,欲使静态电流IC减小,集电结和发射结的偏置情况为()。保持U,减小RC
保持U,RC一定,增大U
保持RB,RC一定,减小U发射结反偏,集电结正偏
发射结、集电结均反偏#
发射结、集电结均正偏
发射结正偏,集电
- 要求输出电压幅值为±80的放大器,集成运放应选用()。二极管的死区电压随环境温度的升高而()。通用型
高阻型
高压型#
低功耗型增大
不变
减小#
- 图11-40所示桥式整流电容滤波电路,若滤波电容开路,则用直流电压表测得输出电压Uo为()V。14
12
9#
4.5
- 两级阻容耦合放大电路中,第一级的输出电阻是第二级的()。比例运算电路如下图所示,该电路的输入电阻为()。输入电阻
信号源内阻#
负载电阻零
R1#
无穷大
- 正弦波振荡电路如图11-34所示,其振荡频率为()。f0=1/2πRC#
f0=1/RC
f0=1/2π
f0=RC
- 电路如图11-1所示,电路中VD可视为理想二极管,判断uo的值为()V。在整流电路中,二极管之所以能整流,是因为它具有()。6#
3
-3
9电流放大特性
单向导电的特性#
反向击穿的性能
稳压特性
- 在图11-36所示OCL电路中,输入电压ui为正弦波,VT1、VT2工作在()。甲类状态
乙类状态
丙类状态
甲乙类状态#
- 差分放大电路如图11-20所示,若晶体管VT1、VT2的参数对称,β均为50,rbe均为2.6kΩ。则差模电压放大倍数Aud约为()。LC振荡电路如图11-31所示,振荡频率为()。图11-35所示电路中,已知V=12V,RL=16Ω,输入电压ui为正弦波
- 理想运算放大器的共模抑制比为()。差分放大电路的作用是()。零
约120dB
无穷大#
AU放大差模信号,抑制共模信号#
放大共模信号,抑制差模信号
放大差模信号和共模信号
差模信号和共模信号都不放大
- 电路如图11-12所示,已知U=12V,RC=3kΩ,β=40且忽略Ube,若要使静态时UCE=9V,则风应取()kΩ。图11-42所示整流电路的输出电压Uo为()U21。600
240
480#
3600.45#
0.90
1.10
1.25
- 下列叙述中错误的是()。同相输入比例运算放大器电路中的反馈极性和类型属于()。双端输入差分放大电路的差模输入信号等于两输入端信号的差值
单端输入差分放大电路的共模输入信号等于该输入端信号的一半
双端输入
- 图11-40所示桥式整流电容滤波电路,若滤波电容开路,则用直流电压表测得输出电压Uo为()V。有两个放大器A1和A2分别对同一电压信号进行放大。当输出端开路时,A1和A2输出电压相同。而接入相同的负载电阻后,Vo1>Vo2。
- 集成运放的电压传输特性之中的线性运行部分的斜率愈陡,则表示集成运放的()。欲提高功率放大器的效率,常需要()。闭环放大倍数越大
开环放大倍数越大#
抑制漂移的能力越强
对放大倍数没有影响增加电源供给的功率,