查看所有试题
- ()是指坯壳出结晶器后受到的冷却。二次冷却#
一次冷却
三次冷却
- 转炉炼钢的重要原料是铁水和()。结晶器从最高位置下降到最低位置或从最低位置上升到最高位置所移动的距离,称为()。连铸坯的柱状晶越发达,对钢材的机械性能越()。废钢A.振动周期
B.振幅#
C.频率A.不利#
B.
- 钢中的气体主要有氧气、()和氮气。火焰切割机的主要燃料有()。氢气A.乙炔、煤气、空气
B.乙炔、氮气、氧气
C.乙炔、丙烷、液化气#
- 浇铸温度是()。结晶器内的钢水温度
中间包内的钢水温度#
到达平台的钢水温度
- 根据钢水脱氧程度的不同,可分为镇静钢、半镇静钢和()。板坯浇铸一般使用()质浸入式水口。连铸二次冷却水量分配原则是()。皮下气泡产生的原因是()。气雾冷却比水冷效果要()。沸腾钢A.石英#
B.铝碳
C.粘
- 结晶器锥度大能提高结晶器的传热,但()也随之增大。机械剪主要是应用于()连铸机上。拉坯阻力A.板坯
B.大方坯
C.小方坯#
- 机械剪切主要用在()连铸机上。表面夹渣的产生原因之一是()。小方坯A.结晶器变形
B.结晶器液面波动#
C.钢水硫含量过高
D.钢水温度不均
- 中间包注流的控制方式有()、滑动水口式或定径水口式。塞棒式
- 引锭杆是()和引锭杆本体两部分组成的。中间包永久层一般采用()型。连铸开浇堵引锭头的主要目的是()。()是指坯壳出结晶器后受到的冷却。引锭头A.砌砖#
B.打结
C.挂绝热板
D.涂料A.保温
B.防止二次氧化
- OB是指()。保护渣中Al2O3含量的增加将导致熔渣粘度的()。火焰切割的基本原理与手工气割原理是()的。与其它两种结构相比,中包采用()结构可以改善中包内流股状态,促进夹杂物上浮。冷却结晶器水的水质是()。
- 火焰切割主要是用氧气和各种()配合通过喷嘴实现切割的。减小铸坯振痕的方法是()。燃气A.高频率小振幅#
B.低频率小振幅
C.低频率大振幅
- 火焰切割机的主要参数包括气体压力、耗量、切割速度及()等。采用气洗水口所吹气体一般是()。拉矫机的作用是()。保护渣的水份含量()。弧表连铸机的设备对弧就是()。最小定尺长度A.O2
B.N2
C.CO2
D.Ar#A
- 结晶器的主要工艺参数为()。因化学作用使钢包耐火材料受损坏的是()。保护渣的好坏主要影响铸坯的()。结晶器冷却水的pH值为()。连铸坯的坯壳受到内部钢水静压力有作用而鼓胀为凸面的现象称为()。A、振幅
B
- 铸坯鼓肚属于()缺陷。板坯浇铸一般使用()质浸入式水口。机械剪主要是应用于()连铸机上。立弯式连铸机内部夹杂物偏向铸坯()。连铸浇钢过程中,二冷水压力突然增高,流量同时降低,原因是()。形状A.石英#
B.
- 铸坯的内部缺陷主要决定于在二次冷却区铸坯冷却过程和铸坯()系统。中心裂纹属于()缺陷。结晶器冷却水采用()的方式流动。支撑A.表面
B.内部#
C.形状
D.外部A.低进高出#
B.高进低出
C.高进高出
- 连铸坯凝固结构从边缘到中心是由细小等轴晶带、()和中心等轴晶带组成。机械剪主要是应用于()连铸机上。柱状晶带A.板坯
B.大方坯
C.小方坯#
- 使用较多的浸入式水口有()和双侧孔式两种。浇注温度与拉坯速度密切相关,温度越高,则拉坯速度越()。单孔直筒形A.低#
B.高
C.不受影响
- 气孔和气泡属于铸坯的()缺陷。WJN1000140喷嘴表示喷水角度为()度。在连铸过程中,更换大包时,中间包内液面应处在()。表面A.14
B.100
C.140#A.满包#
B.正常浇注位置
C.临界高度
D.中间包深度的1/2处
- 火焰切割装置的质量()。机械剪主要是应用于()连铸机上。小A.板坯
B.大方坯
C.小方坯#
- 铸机漏钢的原因可分为:控制不好漏钢、()和设备故障漏钢。因化学作用使钢包耐火材料受损坏的是()。钢水从浇注温度冷却到凝固温度释放的热量称为()。工艺不好漏钢A.钢水成份对耐火材料的侵蚀#
B.钢水对耐火材
- 中间包加热的方法很多,生产中使用的主要是感应加热法和()。表面夹渣的产生原因之一是()。中心偏析产生的原因是由于连铸坯的()比较发展引起的。等离子加热法A.结晶器变形
B.结晶器液面波动#
C.钢水硫含量过
- 结晶器润滑剂有油润滑和()润滑。采用()的措施,可以提高火焰切割速度。保护渣A.提高拉坯速度
B.改进割枪构造#
C.改善铸坯质量
- 钢水在结晶器内凝固形成的坯壳所放出的热量主要是()带走的。冷却结晶器水的水质是()。冷却水A.软水#
B.硬水
C.浊环水
- 在连铸坯表面上沿浇铸方向走向的裂纹叫().纵裂
- 中间包液面高度检测的方法有磁浮法、热电偶法、()法和红外线法。同位素
- 铸坯表面缺陷主要指()、夹渣、气孔等。热送热装,利用的是铸坯的()。裂纹A.过热
B.潜热
C.显热#
- 在凝固过程中形核的两种方式是()形核和非自发形核。连续铸钢的三大工艺制度是()。自发A.炉机匹配制度、冷却制度、温度制度
B.温度制度、拉速制度、冷却制度#
C.铸坯切割制度、拉速制度、保温制度
- 连铸机上使用的压力喷嘴,其结构形工有扁嘴、()、螺旋形喷嘴。中心裂纹属于()缺陷。正常浇注时,更换结晶器保护渣应()。结晶器的主要工艺参数为()。圆锥形喷嘴A.表面
B.内部#
C.形状
D.外部A.适当降速#
B
- 钢水在结晶器中的冷却叫()冷却。板坯浇铸一般使用()质浸入式水口。一次A.石英#
B.铝碳
C.粘土
D.锆
- 铸坯表面上常见的一种无明显方向和位置的成组的晶间裂纹,称之为()。板坯浇铸一般使用()质浸入式水口。星状裂纹A.石英#
B.铝碳
C.粘土
D.锆
- 结晶器润滑剂有()润滑和保护渣润滑。结晶器内液面波动时,保护渣的加入应在液面()过程中完成。中间包烘烤,点火操作程序正确的是()。弧表连铸机的设备对弧就是()。油A.下降
B.上升#
C.中间位A.先点火再开
- 加入到结晶器的保护渣,在钢液面上形成了液渣层、()和粉渣层的三层结构。采用气洗水口的主要作用是()。造成水口结瘤的主要原因是:()。烧结层A.降低成本
B.防止水口堵塞#
C.提高钢产量
D.均匀成份温度A.液
- 结晶器保护渣主要理化性能有化学成份、()、粘度、熔化速度、辅展性、水份。在单位时间内消耗的冷却水量与通过二次冷却段的铸坯重量的比值,称为()。熔化温度A.比水量#
B.冷却比
C.压缩比
- 用相纸显示试样上硫的偏析的方法叫()。与其它两种结构相比,中包采用()结构可以改善中包内流股状态,促进夹杂物上浮。硫印A.无挡渣墙
B.单挡渣墙
C.双挡渣墙#
- 火焰切割机主要由切割小车及其行走机构,()及其传动机构以及氧气,可燃气管路系统组成。镁砖属于()耐火材料。结晶器从最高位置下降到最低位置或从最低位置上升到最高位置所移动的距离,称为()。WJN1000140喷嘴表
- 为避免结晶器水冷表面形成水垢,降低冷却效果,结晶器必须用()冷却。结晶器内热量传递路线为钢水→凝固坯壳→渣膜气隙铜壁冷却水,其中传热最大的障碍是()。软水A.渣膜
B.气隙#
C.铜壁
D.冷却水
- 吹氩的目的是()。A、降温
B、均匀温度#
C、造泡沫渣
D、脱氧
- 铸坯内部缺陷主要是内部裂纹、()、中心疏松、非金属夹杂物。水平连铸机内部夹杂物偏向铸坯()。中心偏析A.上面
B.下面#
C.中心位置
D.无夹杂
- 火焰切割枪的传动机构包括()机构和升降机构。边角裂属于()缺陷。火焰切割一般不适用于()连铸机上。立弯式连铸机内部夹杂物偏向铸坯()。横移A.内部缺陷
B.外部缺陷#
C.形状缺陷A.小方坯#
B.大方坯
C.圆
- 铸坯缺陷分为表面缺陷、()和形状缺陷。碳粒在连铸保护渣中起着的()作用。在单位时间内消耗的冷却水量与通过二次冷却段的铸坯重量的比值,称为()。内部缺陷A.熔速调节剂#
B.助熔剂
C.基础渣料A.比水量#
B.