查看所有试题
- 下述说法中不属于保护渣冶金特性的是()。A.粘度
B.溶解Al2O3能力
C.粒度#
- 正常浇注时,更换结晶器保护渣应()。铸坯的内部缺陷主要决定于()铸坯的冷却过程。A.适当降速#
B.不降速
C.大幅降速A.结晶器
B.二冷段#
C.矫直点
- 采用气洗水口所吹气体一般是()。连铸坯切割长度是按()要求确定的。A.O2
B.N2
C.CO2
D.Ar#A.液芯长度
B.连铸机长度
C.铸坯断面
D.轧钢#
- 连续铸钢的三大工艺制度是()。A.炉机匹配制度、冷却制度、温度制度
B.温度制度、拉速制度、冷却制度#
C.铸坯切割制度、拉速制度、保温制度
- 在连铸过程中,更换大包时,中间包内液面应处在()。A.满包#
B.正常浇注位置
C.临界高度
D.中间包深度的1/2处
- 在铸坯横断面和纵断面上出现的碳、磷和硫等元素的浓度偏差,称为铸坯的()。A.偏析#
B.疏松
C.缩孔
- 气水雾化喷嘴较普通喷嘴()。A.冷却效率低
B.设备复杂#
C.耗水量大
D.能达到弱冷却
- 回转台的主要作用是:()。连铸坯的冷却主要的传热方式是()。A.能快速交换盛钢桶,而不降低拉坯速度#
B.便于盛钢桶升降、吊运
C.便于检修维护A.辐射传热#
B.对流传热
C.传导传热
- 保护渣的溶化温度取决于渣的()。A.化学成分#
B.碱度
C.粒度
- 结晶器的振幅等于行程的()。连铸机使用的冷却水有()。A.1/2#
B.1/3
C.1倍A.机械闭路水
B.机械开路水
C.机械闭路和开路水#
- 结晶器从最高位置下降到最低位置或从最低位置上升到最高位置所移动的距离,称为()。保护渣的溶化温度取决于渣的()。A.振动周期
B.振幅#
C.频率A.化学成分#
B.碱度
C.粒度
- 若不及时将“渣条”捞出,不仅有漏钢危险,而且会造成连铸坯的()质量缺陷。A.表面龟裂
B.夹渣#
C.气泡
- 结晶器内热量传递路线为钢水→凝固坯壳→渣膜气隙铜壁冷却水,其中传热最大的障碍是()。浇铸温度是()。A.渣膜
B.气隙#
C.铜壁
D.冷却水结晶器内的钢水温度
中间包内的钢水温度#
到达平台的钢水温度
- 为了减小铸坯表面振痕,结晶器振动采用()。A.高频率大振幅
B.低频率大振幅
C.高频率小振幅#
- WJN1000140喷嘴表示喷水角度为()度。铸坯中心线裂纹属于()。A.14
B.100
C.140#A.表面缺陷
B.内部缺陷#
C.形状缺陷
- 在浇钢过程中,结晶器正常液面应控制距结晶器上口()处。连铸浇钢过程中,二冷水压力突然增高,流量同时降低,原因是()。连铸机大包与中间包的长水口保护浇注是防止()。A.50mm
B.100mm#
C.150mmA.水管脱落
B.
- 表面夹渣的产生原因之一是()。气水雾化喷嘴较普通喷嘴()。A.结晶器变形
B.结晶器液面波动#
C.钢水硫含量过高
D.钢水温度不均A.冷却效率低
B.设备复杂#
C.耗水量大
D.能达到弱冷却
- 火焰切割机的主要燃料有()。A.乙炔、煤气、空气
B.乙炔、氮气、氧气
C.乙炔、丙烷、液化气#
- 连铸机使用的冷却水有()。A.机械闭路水
B.机械开路水
C.机械闭路和开路水#
- 铸坯的内部缺陷主要决定于()铸坯的冷却过程。A.结晶器
B.二冷段#
C.矫直点