查看所有试题
- 在设备调试时,观察示波器区域,调制盘信号应在()V左右。A、-5
B、-4
C、0#
D、5
- 轴箱测温成绩评判时,中低温偏差2度,成绩为()。合格
良好
不合格
优秀#
- 从来车的方向开始算起,第一个为2#磁头,第二个为3#磁头,从来车的反方向开始算起,第二个为3#磁头,第三个为4#磁头
2#、3#、4#号磁头是根据三个磁头的相对位置来确定,从来车的方向开始算起,第一个为4#磁头,第二个为3#磁
- THDS-A红外轴温探测系统探测站软件的工作模块运行需要硬件设备()卡和数字IO卡的支持,因此运行前需要安装好这两种卡的驱动程序,并做好相应的配置。THDS-A红外轴温探测系统AD采集卡是()总线。A、AD模拟采集卡#
B、
- THDS-A轴温探测系统能适应的交流供电电源(220V)频率范围是()50~60Hz#
50~70Hz
50~80Hz
50~90Hz
- 红外线动态检测车在评判地面站测温精度中,中低温轴温误差优秀的标准是()。测量THDS-A红外轴温探测系统热敏探头噪声的方法正确的是()<︱±2︱℃
<︱±3︱℃#
<︱±4︱℃
<︱±6︱℃进入系统维护状态,用示波器
- 红外线轴温探测设备,是利用现代红外辐射探测技术对每个轴箱发出的红外辐射强度大小进行探测,并将其转换为相应的()进行处理,从而达到轴温检测和发现热轴的目的。光信号
电信号#
化学信号
模拟信号
- THDS-A红外轴温探测系统如果报调制盘频率故障,正确的解决办法是()。更换探头
更换测温板
左右侧探头互换,故障也互换,则需要更换探头。若故障不移动,更换模拟信号调理板。若两侧频率同时有异常,检查电源箱调制电源
- 探测站设备进入接车状态时,控制箱上的功放板指示灯显示描述不正确的是()内探功放板电源指示灯亮
大门控制指示灯亮
外探功放板电源指示灯亮
内探功放板挡板控制灯亮#
- 搬运易燃、易爆物品,应事先选择存放地点和通过地段,()米以内不得应有明火。THDS-A红外轴温探测系统中交流传感器输出对应交流电压AC()。5
10#
C、8A、0、0~220V
B、0、0~300V
C、0、0~380V
D、0、0~440V#
- PDS主要功能是识别运行状态不良的车辆、识别车轮()、测量车辆装载的超偏载状态。THDS-A探测系统工控机内电路板的大修检标准是()踏面擦伤#
踏面剥离
温度直接更换#
器件外观正常
无扭曲变形,无烧焦斑痕,接插脚无
- THDS-A探测系统中探头按测温元件不同划分为()下列哪个不属于THDS-A红外轴温探测系统探测站轨边设备()热敏探头和光子探头#
调制探头和光子探头
热敏探头和直流探头
调制探头和直流探头红外轴箱扫描器(内装探头)
- 车辆滚动轴承使用的润滑脂是()。单路电源的THDS探测站须配备()在线式UPS不间断电源。3号钙基脂
30号钠基脂
3号锂基脂#
3号钙钠基脂4h
8h#
2h
10h
- HTK型红外线轴温探测设备光子探头的电缆线长26m,应把加热板上的跨线套接到()以上。10m
20m
30m#
40m
- 控制柜中有()加温保护板。THDS-A探测站设置间隔()公里。1块
2块#
3块
4块20
25
45
30#
- 红外线设备第一次大、中修以设备试运行年度为起点计算,当多种检修修程重叠时,以()修程为主。TFDS探测站、列检检测站电力电源故障或电压超限时,由()通知供电部门处理,同时报铁路局车辆运行安全监测站备案。高级#