查看所有试题
- 低压轴封送汽投入后,应注意充分暖管,并应维持进汽温度()℃。150
- 当使用低压旁路运行时,汽轮机排汽缸真空度大于()kPa。75
- 启动过程冲转前要进行凝结水系统冲洗,()恢复系统停止放水。合格后
- 在启动过程中,当油箱油温达()℃时,冷油器应通水以维持正常油温。喷嘴配汽式汽轮机,在1号调节阀开启过程中,调节级理想焓降是()。45A、不变;
B、减小;
C、增加;#
D、难于确定
- 对于采用喷嘴调节的汽轮机调节级,其最危险的工况发生在第一个调速汽门全开而()的工况。第二个调速汽门尚未开启
- 用旁路门冲转机组时,应考虑旁路门的通流能力,选定的参数应能通过()并达到()。临界转速;定速
- 当()时,柴油发电机自启动。A、机组跳闸;
B、当高压厂用变压器或启动变压器跳闸;#
C、保安电源高电压;
D、保安电源进线过电流未动作。
- 从理论上讲,发生油膜振荡的汽轮机转速等于()。A、2倍一阶临界转速;#
B、一阶临界转速;
C、涡动速度;
D、额定转速。
- 开关送电前进行拉合试验,其目的是()。A、检查三相是否同期;
B、检查分合闸回路是否正常;#
C、检查保护回路是否正常;
D、检查遥控操作是否正常。
- 启动发电机密封油系统时,应先投入()侧密封油泵,后投入()侧密封油泵。空气;氢气
- 所谓合理启动,就是寻求合理的加热方式,在启动过程中使机组各部分的()、()、()和()等均维持在允许范围。正常冷态启动升速时,转子芯孔表面受到的应力是()。热应力;热变型;振动;胀差A、热压应力与离心力之
- 当润滑油温较()时,可以启动润滑油泵进行循环提升()。喷嘴配汽式汽轮机有4个调节阀,当2号调节阀开启过程中,3号、4号调节阀后的压力是()。对()渗透油层,聚合物降低渗透率的主要机理是吸附。低;油温A、零;
B
- 正常冷油器入口油温度在()℃,允许偏差±()℃。汽轮机启动过程中,减小临界转速共振损害的一般方法是()。60;10A、加强对转子的平衡;
B、降低运行转速;
C、迅速平稳地通过临界转速;#
D、增大轴承比压来增大轴承
- 对于调节级动叶强度来讲,最危险工况是()。A、第一调节阀刚全开时的负荷;#
B、最大负荷;
C、第一调节阀刚开时的负荷;
D、去负荷。
- 从理论上讲,发生油膜振荡的汽轮机转速等于()。A、2倍一阶临界转速;#
B、一阶临界转速;
C、涡动速度;
D、额定转速。
- 对()渗透油层,聚合物降低渗透率的主要机理是吸附。A、高
B、中
C、高、中#
D、低
- 当机组负荷正常后或再热器冷段压力大于()kPa时,15ata辅汽汽源可倒换为冷再热供汽。1960
- 当锅炉主蒸汽压力大于()kPa时,可将辅汽联箱供汽侧由本机组带。3920
- 汽轮机冷态启动过程中,当转速达到2700r/min时,应进行危急保安器()试验。充油闭锁跳闸
- 第一台循环水泵允许启动条件规定,凝结器的一侧出口门开()%,人口门两侧至少有一个()。20;全开
- 汽缸预热时,应防止()使导管压力逐步提高,控制温升率小于()℃/h。冲车时,要把温差调到()℃以下。转子冲动;83;55
- 汽轮机启动时,应使主蒸汽参数与高压汽缸第一级金属内壁温度匹配,其理想数值为()℃,可接受数值+()℃、-()℃,其极限数值为+()℃、-()℃。轴颈产生半速涡动的因素是()。GE352MW汽轮机中压缸启动时的返流方式的最
- 在转子进行预热工作时,真空应大于()kPa,逐步开尾部加热门,控制升温率在()℃/h。当高压缸金属温度加热到()℃以上,维持压力在()kPa,按曲线要求维持预热时间。68;55;150;470.4~568.4
- 当主蒸汽温度比调速汽门外表金属温度高()℃以上时,要进行汽缸预热。120
- 汽轮机冷态启动时,汽缸外壁受到()应力。由于汽轮机启动和升负荷速度控制不当,造成汽缸法兰的内、外壁温差过大,使法兰结合面受到挤压而产生塑性变形。当汽缸内、外壁温差平稳后,在高压端法兰结合面处将产生()。A
- 汽轮机启动时,当高压缸内壁金属温度小于()℃时,要进行转子预热工作。150
- 汽轮机冷态启动前进行EHC检查时,应使初压限制器在()位置,负荷限制器在()位置,预热在()位置,热态/冷态方式在()位置,转速设定在()位置,进行方式指示()。切除;零;切除;冷态;阀门关闭;全周进汽
- 在汽轮机启动时,应尽快提高转子温度到脆性转变温度以上,以增强转子对()和()的承受能力。由于汽轮机启动和升负荷速度控制不当,造成汽缸法兰的内、外壁温差过大,使法兰结合面受到挤压而产生塑性变形。当汽缸内、外
- 热疲劳是金属零件在()反复作用下遭到破坏的现象。汽轮机热态启动的起始负荷是()。交变热应力A、低负荷暖机所需要的5%~10%额定负荷;
B、启动前汽缸调节级处的金属温度所对应的汽轮机负荷;#
C、80%额定负荷
- 汽轮机启停或变工况运行时,金属材料除受到热应力作用外,同时还受到()应力的影响。机械
- 当汽轮机转子膨胀值小于汽缸膨胀值时,相对膨胀差为()。负值
- 通常,只要在零部件内部存在(),就会产生热应力。温差
- 当在汽轮机加热或冷却时,如果零部件在膨胀中受阻,则产生()应力。热
- 通常,我们将由温差引起的变形称为()。轴颈产生半速涡动的因素是()。热变形A、不平衡离心力的作用;
B、油膜失稳力的作用;#
C、轴颈转动时油膜阻力的作用;
D、转子质量分力的作用。
- 在汽轮机加热或冷却时,如果零件热变形受到约束,则在零件内部将产生()。热应力
- 汽轮机冷启动时,凝结放热结束后蒸汽便以()方式向金属传递热量。喷嘴配汽式汽轮机有4个调节阀,当2号调节阀开启过程中,3号、4号调节阀后的压力是()。对流放热A、零;
B、一、二喷嘴后压力;#
C、新蒸汽压力;
D、
- 在冷启动的初期,蒸汽对转子的放热属于()放热。珠状凝结
- 喷嘴配汽式汽轮机,在1号调节阀开启过程中,调节级理想焓降是()。A、不变;
B、减小;
C、增加;#
D、难于确定
- 从理论上讲,发生油膜振荡的汽轮机转速等于()。A、2倍一阶临界转速;#
B、一阶临界转速;
C、涡动速度;
D、额定转速。
- 喷嘴配汽式汽轮机在1号调节阀全开时,可带50%额定负荷,则汽轮机调节级的最危险工况将发生在()。A、超负荷;
B、低负荷;
C、空负荷;
D、50%负荷#