查看所有试题
- YJ27滤嘴接装机滤嘴烟支切刀磨刀砂轮的调整要求和滤棒切刀磨刀砂轮的调整要求相同。YJ29滤嘴接装机烟支切刀磨刀砂轮由()驱动。YJ27滤嘴接装机为保证滤棒切割质量,调整滤棒切刀与磨刀砂轮的位置时,应使切刀两侧均匀
- YJ29滤嘴接装机,调整滤嘴烟支切刀前磨刀砂轮时,逆时针旋转调节螺钉,可增大磨刀砂轮对切刀的磨削量。YJ29滤嘴接装机水松纸搭接时储纸箱的储纸长度为()m。YJ29滤嘴接装机水松纸储纸箱导向座必须相对于机身定位,其距
- YJ27滤嘴接装机滤嘴烟支切刀磨刀砂轮只有在与旋转的切刀接触时才被驱动。YJ29滤嘴接装机水松纸搭接指令开始后,拉纸辊超量供纸,速度可达正常的()%。正确#
错误106
114
108
112#
- YJ29滤嘴接装机,调整滤嘴烟支切刀后磨刀砂轮时,顺时针旋转调节螺钉,可增大磨刀砂轮对切刀的磨削量。正确#
错误
- YJ29滤嘴接装机,通过改变滤嘴烟支切割鼓轮导块支撑横梁与导块横板的相对位置,可对里外滤嘴烟支长度进行微调。正确#
错误
- YJ29滤嘴接装机滤嘴烟支切割鼓轮内、外端部导轨之间的距离等于双倍长滤嘴烟支的长度。YJ29滤嘴接装机水松纸储纸箱导向座必须相对于机身定位,其距离为()mm。YJ27滤嘴接装机胶缸组件中控胶辊滚针轴承的润滑是通过(
- YJ29滤嘴接装机调整滤嘴烟支切割鼓轮内、外端部导轨时,应使它们和鼓轮同轴,并且下缘与鼓轮槽底同高。YJ29滤嘴接装机水松纸搭接指令开始后,拉纸辊超量供纸,速度可达正常的()%。正确#
错误106
114
108
112#
- YJ29滤嘴接装机双倍长滤嘴烟支由内、外端部导轨固定在切割鼓轮烟槽中。YJ27滤嘴接装机烟支切刀紧固螺栓为()螺纹。YJ29滤嘴接装机胶辊干燥线中心距主机座前壁面的距离为()mm。YJ27滤嘴接装机胶缸总成若要从弯臂上
- YJ27滤嘴接装机成形后的双倍滤嘴卷烟最后在归位轮的辅助作用下落入搓接鼓轮烟槽。YJ27滤嘴接装机胶缸总成若要从弯臂上取出,应将手柄转向()侧。正确#
错误右#
左
里
外
- YJ27滤嘴接装机靠拢鼓轮浮圈装置调整过程中,若要向前移动卷烟轴向位置,应逆时针方向转动两个滚轮臂的调节螺钉。YJ29滤嘴接装机烟支切割鼓轮刀槽中心距机器墙板的距离为()mm。正确#
错误160
180
200#
220
- YJ27滤嘴接装机靠拢鼓轮浮圈装置调整过程中,若要向后移动卷烟轴向位置,应逆时针方向转动两个滚轮臂的调节螺钉。YJ27滤嘴接装机烟支切刀紧固螺栓为()螺纹。正确#
错误右旋#
左旋
梯型
细牙
- YJ27滤嘴接装机若要增大靠拢鼓轮两个浮圈之间的距离“X”,可顺时针方向转动前滚轮臂调节螺钉和逆时针方向转动后滚轮臂调节螺钉。正确#
错误
- YJ27滤嘴接装机若要减小靠拢鼓轮两个浮圈之间的距离“X”,可顺时针方向转动前滚轮臂调节螺钉和逆时针方向转动后滚轮臂调节螺钉。YJ29滤嘴接装机烟支切刀磨刀砂轮由()驱动。YJ27滤嘴接装机滤棒切刀磨刀砂轮调节手轮(
- YJ27滤嘴接装机轴向调整靠拢鼓轮浮圈装置时,应使浮圈内缘到机器中心线的距离等于烟支长度。YJ29滤嘴接装机烟支切刀紧固螺栓是()螺纹。YJ29滤嘴接装机水松纸胶后加热器导板的中心距接装机机身前面板的距离为()mm
- YJ27滤嘴接装机靠拢鼓轮浮圈内缘到机器中心线的距离通过隔套的尺寸来控制。YJ27滤嘴接装机调整滤棒切刀磨刀砂轮时,应使砂轮盖过刀刃约()mm。YJ29滤嘴接装机水松纸胶后加热器导板的中心距接装机机身前面板的距离为
- 可使用酒精清洁擦净YJ27滤嘴接装机胶辊、回收盘上的胶。YJ29滤嘴接装机烟支切刀磨刀砂轮由()驱动。YJ29滤嘴接装机水松纸储纸箱导向座必须相对于机身定位,其距离为()mm。正确#
错误齿形带
三角带
“O”型圈
圆形带#
- YJ27滤嘴接装机控胶辊与上胶辊之间的胶堆大小由光传感器监测,若胶堆减小到光传感器监测不到时,则显示接装机无胶水停机。正确#
错误
- 船轴发生磨损的部位主要是()。YJ29滤嘴接装机水松纸储纸箱主要由()、压轮、有机玻璃护门、支撑杆、导辊等组成。轴颈
工作轴颈#
法兰
法兰连接面供纸辊
拉纸辊#
压纸辊
加速辊
- YJ27滤嘴接装机胶缸组件中控胶辊滚针轴承、上胶辊轴和孔的润滑每8小时需进行一次。正确#
错误
- YJ29滤嘴接装机控胶辊的轴向位置,可根据滤嘴烟支分切后的干燥线位置进行调整。YJ27滤嘴接装机胶缸组件中控胶辊滚针轴承、上胶辊轴和孔的润滑每()小时需进行一次。YJ27滤嘴接装机靠拢鼓轮左上方导纸板的作用是防纸
- YJ29滤嘴接装机在拆下胶辊组件之前不必停止胶泵电机。YJ27滤嘴接装机烟支切割鼓轮上的浮圈经()与固定圈连接,固定圈固定在鼓轮上。正确#
错误拉伸弹簧#
螺钉
刚性材料
销
- YJ29滤嘴接装机在正常的生产过程中,可以取下胶辊的侧盖,用潮湿的布清洁胶辊。YJ29滤嘴接装机水松纸搭接指令开始后,拉纸辊超量供纸,速度可达正常的()%。正确#
错误106
114
108
112#
- YJ29滤嘴接装机机器运行过程中,可根据滤嘴烟支分切后里外水松纸宽度对胶后加热器导板进行微调。YJ27滤嘴接装机调整滤棒切刀磨刀砂轮时,应使砂轮盖过刀刃约()mm。正确#
错误8~10#
10~12
6~8
4~6
- YJ29滤嘴接装机当水松纸宽度改变时,胶后加热器导板必须重新调整。YJ29滤嘴接装机烟支切刀紧固螺栓是()螺纹。正确#
错误右旋
左旋#
管
细牙
- YJ29滤嘴接装机调整胶后加热器导向板角度时,应使水松纸能平滑通过到达水松纸切纸鼓轮。YJ29滤嘴接装机烟支切刀组件内、外端部导轨之间的距离为双倍长度烟支加()mm。正确#
错误1.5
0.2
0.5#
1
- YJ29滤嘴接装机调整胶后加热器导向板前,不必将胶后加热器锁固在其工作位置。YJ27滤嘴接装机烟支切割鼓轮上的浮圈经()与固定圈连接,固定圈固定在鼓轮上。YJ29滤嘴接装机三段滤嘴段在排直鼓轮上形成一列并对齐,滤嘴
- YJ29滤嘴接装机水松纸胶后加热器导板的中心距接装机机身前面板的距离为225mm。正确#
错误
- YJ29滤嘴接装机当胶前加热器导向板角度发生改变时,胶前加热器的导向板不必重新调整。YJ29滤嘴接装机调整胶前加热器导向板时,应保证水松纸中线到机身的前面板的距离为()mm。船轴发生磨损的部位主要是()。正确#
错
- 调整YJ29滤嘴接装机胶前加热器导向板时,应使水松纸能平滑通过并到达上胶辊。YJ29滤嘴接装机烟支切刀磨刀砂轮由()驱动。YJ29滤嘴接装机烟支切刀紧固螺栓是()螺纹。YJ29滤嘴接装机,可用()清洁保养滤嘴传送鼓轮刮
- YJ29滤嘴接装机水松纸胶前加热器对涂胶前的水松纸进行预热,将水松纸干燥、平整,以便于涂胶均匀。正确#
错误
- YJ29滤嘴接装机当水松纸宽度改变时,胶前加热器的导向板不必重新调整。YJ27滤嘴接装机烟支切割鼓轮上的浮圈经()与固定圈连接,固定圈固定在鼓轮上。YJ29滤嘴接装机,可用()清洁保养滤嘴传送鼓轮刮刀和铲刀组件。YJ2
- YJ29滤嘴接装机水松纸储纸箱导向座必须相对于机身定位,其距离为200mm。YJ29滤嘴接装机烟支切刀组件内、外端部导轨之间的距离为双倍长度烟支加()mm。YJ29滤嘴接装机烟支切割鼓轮刀槽中心距机器墙板的距离为()mm。
- YJ29滤嘴接装机水松纸储纸箱的导向座不可调换工作面。正确#
错误
- YJ29滤嘴接装机水松纸储纸箱中控纸臂的上下移动可控制拉纸辊的转速,使水松纸的供应与消耗匹配。YJ29滤嘴接装机烟支切刀磨刀砂轮由()驱动。YJ29滤嘴接装机水松纸胶后加热器导板可调节水松纸的里外长度,确保水松纸上
- YJ29滤嘴接装机,可使用温水或湿布清洁水松纸储纸箱的各支撑杆、有机玻璃、拉纸辊、压轮、导块。YJ29滤嘴接装机水松纸搭接指令开始后,拉纸辊超量供纸,速度可达正常的()%。正确#
错误106
114
108
112#
- YJ29滤嘴接装机,在进行水松纸储纸箱的清洁保养前,应先按下接装机控制面板上的水松纸手动进料按钮,抑制自动搭接程序。正确#
错误
- YJ27滤嘴接装机滤棒切刀磨刀砂轮在轴向上不能有游隙。YJ29滤嘴接装机三段滤嘴段在排直鼓轮上形成一列并对齐,滤嘴段的中心处于()中心线上。正确#
错误传送鼓轮
错位鼓轮
排直鼓轮
汇合鼓轮#
- YJ27滤嘴接装机滤棒切刀磨刀装置手轮逆时针方向转动,可增大磨刀压力。YJ27滤嘴接装机胶缸组件中控胶辊滚针轴承、上胶辊轴和孔的润滑每()小时需进行一次。正确#
错误3
6
8#
10
- YJ27滤嘴接装机顺时针方向转动滤棒切刀磨刀装置手轮,可增大磨刀压力。YJ29滤嘴接装机烟支切刀组件内、外端部导轨之间的距离为双倍长度烟支加()mm。YJ29滤嘴接装机水松纸胶后加热器导板可调节水松纸的里外长度,确保
- YJ29滤嘴接装机安装排直鼓轮滤棒导板和铲刀组件时,首先应确保滤嘴错位鼓轮和排直鼓轮正确定位。正确#
错误