查看所有试题
- 多腔压力容器的各腔类别不同时,应按类别最高提出设计、制造要求。正确#
错误
- 没有国家标准和行业标准,企业标准不能作为压力容器检验的依据。正确#
错误
- 不具备注册条件的压力容器,不能发给使用证。正确#
错误
- 压力容器的内外部检验,其检验内容不包括压力容器的外部检查内容。正确#
错误
- 力容器注册后,即可办理压力容器使用证。正确#
错误
- 力容器必须逐台办理压力容器使用登记手续。正确#
错误
- 用压力容器外部检查、内外部检验内容及安全状况等级的规定,按《压力容器安全技术监察规程》执行。正确#
错误
- 压试验包括液压试验、气压试验气密试验。正确#
错误
- 力容焊后热处理,应在焊接结束后并检测合格后,耐压后进行。正确#
错误
- 台压力容器如果同时具备两种以上的工艺作用原理,应按工艺过程中主要作用来划分品种。正确#
错误
- 压力容器安全技术监察规程》规定,低压容器均为第一类压力容器。正确#
错误
- 腔压力容器,按照类别高的压力腔作为容器的类别进行使用正确#
错误
- 器内主要介质为最高工作温度低于标准沸点的液体时,气相空间大于0.025m3,且最高工作压力大于0.1Mpa,也属于压力容器。正确#
错误
- 锅炉、压力容器的单位在与外商签定合同时,一般应以我国的规程、标准为设计、制造、安装、检验的依据。正确#
错误
- 在某种化学介质中,通以一定的阳极电流,能够引起钝化的金属,原则上都可以采用阳极保护的方法来防止腐蚀正确#
错误
- 积小于0.025m3的高压容器属于《压力容器安全技术监察规程》的监察范围。正确#
错误
- 耐火混凝土都是由胶粘剂,集料,掺和料按一定比例用水调制成。正确#
错误
- 力容器耐压试验时,由试验压力降到试验压力的80%,进行泄露检查,为维持检查期间压力不变,应采取连续加压的方法。正确#
错误
- 力容器的安全状况等级确定后不应再变更。正确#
错误
- 用锅炉、压力容器的定期检验必须包括对安全附件的检验。正确#
错误
- 后热处理应在耐压试验前进行。正确#
错误
- 用压力容器的内外表面不允许有裂纹。正确#
错误
- 对于外表面有覆盖层的压力容器,应先在外表面局部或全部拆除覆盖层进行检验。正确#
错误
- 用超声波测厚仪对临氢介质压力容器进行壁厚测定时,发现测量值大于壁厚,而判定壁厚的实际尺寸大于壁厚实际尺寸。正确#
错误
- 验员无权根据检验的具体情况,增减检验项目。正确#
错误
- 力容器报废后,应办理报废注销手续。正确#
错误
- 变压力容器的使用条件(压力、温度、介质、用途)时,应到技术监督部门办理变更手续。正确#
错误
- 酚醛玻璃棉的最高使用温度为350℃正确#
错误
- 呋喃树脂漆耐大多数酸,碱盐及有机溶剂,但不耐氧化剂正确#
错误
- 玻璃纤维保温毡的最高耐热温度是450℃正确#
错误
- 在合成橡胶中,丁腈橡胶的耐热性最好正确#
错误
- 一般情况下,橡胶分为天然橡胶和合成橡胶两大类正确#
错误
- 生橡胶加入硫磺后形成稳定体,硫磺含量1—3%时叫做软橡胶,含量大于3%时叫做硬橡胶正确#
错误
- 在进行埋地管道施工时,为了便于下管,管沟施工时挖出来的土宜放在沟边,土堆与沟边的最小距离不得小于0.5米正确#
错误
- 在涂料牌号中,符号“F”表示环氧树脂漆正确#
错误
- 锌黄底漆可以用于黑色金属的涂层正确#
错误
- 涂料一般由不挥发分和挥发分两部分组成。正确#
错误
- 在验收绝热工程时,用表面温度计测量保护层外壁,轴向同侧一米内任意两点的温度不得有明显差异正确#
错误
- 绝热结构一般由防锈层,绝热层,保护层,防潮层构成。正确#
错误
- 耐温800℃以上的保温材料称作耐火材料正确#
错误