查看所有试题
- 电炉炉膛尺寸决定于冶炼铁合金的()、变压器()、操作要求以及电炉机械化程度。为了降低电解液中铜含量开设()品种;功率A、脱铜槽#
B、尾板槽
C、残极槽
D、电解槽
- 常用的渣罐有()和()两种,我厂使用的使用的是方口渣罐。圆口;方口;方口
- 锰硅合金是炼钢常用的()又是生产中低碳锰铁和电硅热法生产金属锰的()。复合脱氧剂;还原剂
- 锰硅生产中,用碳从液态炉渣中还原硅和锰硅合金的总反应式为()MnO·SiO2+3C=MnSi+3CO
- 电炉普遍采用()变压器、三个()变压器供电,这样短网结构更(),便于各相功率()。对电解精炼过程危害比较大的杂质为()三相;单相;合理;调节Pb和Zn
Au和Ag
As、Sb、Bi#
- 电炉主厂房炉子间要进行以下各项作业:电炉()、()操作;()操作;()电极;维修机械和()设备等。装料;冶炼;出铁出渣;接放;电气
- 常用的锭模有()和()两种,浇注75%硅铁使用的是()。浅锭模;深锭模;浅锭模
- 冶炼锰硅合金要求锰矿要有更高的()和(),所用的锰()越高,各项指标越好。提高碱性耐火材料的抗水化性,通常采用的方法是()对使用过的镁铝砖进行分析时发现,由于()的存在,提高了低熔物的耐火度,因而可以减缓炉
- 硅石从β石英转化成鳞石英,体积发生明显的(),也就是硅石在冶炼过程中发生()的主要原因。膨胀;爆裂
- 生产锰硅合金可使用()和几种锰矿(包括富锰渣)的混合矿。底吹炉入炉料水分一般不大于()一种锰矿A、15%
B、10%
C、8%#
D、4%
- 向炉内加料的方法一般有二种,一种是()法,另一种是()法。少加勤加;分批集中加料
- 锰硅合金冶炼中合金中硅低碳高,渣中跑锰多说明()。碱度太低
- 炉内电流电路可简化为二路。即电极→电弧→熔融物→电弧→另一根电极的(),电极→炉料→另一根电极的()。主电路;支路
- 出铁结束的标志是铁流量()和()外逸。减小;炉气
- 锰硅合金冶炼中,炉渣的流动性和碱度直接相关,炉渣稀说明碱度就(),炉渣稠说明碱度就()。铜锍吹炼过程中除S阶段发生在()影响耐火制品抗热震性指标的主要原因是制品的()性质。诺兰达熔池熔炼工艺渣含铜一般为(
- 锰硅合金冶炼工艺中,配料比的主要问题是()的问题。配碳量
- 冶炼含硅量较高的锰硅合金时,除适当增加()的用量外,关键是提高()。还原剂;炉内的温度
- 生产锰硅合金的主要原料有()、()、()、焦炭、白云石(或石灰石)和()。锰矿;富锰渣;硅石;萤石
- 制造电极糊的原料由()碳素材料和()材料组成。固体;粘结
- 无生产硅铁用碳质还原剂,在矿热炉中冶炼,采用()法。电热
- 新开炉生产前要对电炉进行烘炉,目前大中型铁合金电炉直接采用()法进行开炉操作。艾萨炉控制中,熔炼池温度过高而跳闸的现象,将会引起喷枪提升机构快速提升的执行,其中熔池温度高高报警的设定值()℃,时间达到()秒
- 铁合金电炉炉顶上料通常采用料车式()和()输送机上料。提高碱性耐火材料的抗水化性,通常采用的方法是()斜桥;胶带提高烧成温度使其死烧。
使CaO、MgO等生成稳定的化合物。
加保护层减少与大气接触。
A、B和C。#
- 电热法生产铁合金其冶炼过程的热量来源主要是(),使用()还原剂还原矿石中的(),采用连续式的操作工艺,在还原电炉中进行。下列绝热材料属于中低温绝热材料的是()电能;碳质;氧化物石棉制品#
轻质粘土砖
轻质高
- 正确的加料方法,是获得良好炉况、达到高()低的()关键环节之一。铜火法冶炼的主要原料为:()产量;消耗A、硫化铜精矿#
B、氧化铜精矿
C、渣精矿
D、再生铜料
- 出铁时为防止表层铁水凝固,可加入()保温。炭(焦)粉
- 铁合金生产的基本原则是()是基础,()是保障,()是关键。原料;设备;操作
- 为使炉料有一定的透气性,并加速炉料的熔化和还原,要求炉料要有一定的()。镁铬砖中基质的主要成分是()粒度镁铬尖晶石#
镁铝尖晶石
钙镁橄榄石
镁橄榄石
- 电极焙烧速度过快,将导致()增加,导电性和机械强度都有所()。孔隙率;降低
- 矿热电炉按炉缸可分为:()式电炉和()式电炉。转炉吹炼热量主要来源于:()当艾萨排放困难时,可进行压料生产,压料幅度为(),如排放仍然困难,可进一步压料。在排放顺利后逐步恢复料量。固定;旋转A、化学反应热#
- 定时压放电极以补充电极在冶炼过程中的不断()维持电炉的正常工作。诺兰达熔池熔炼工艺渣含铜一般为()。消耗A、1%以下
B、1-3%
C、3-5%#
D、5%以上
- 用基本相同的原料,控制不同的还原温度及还原剂用量,可生产出()的铁合金产品。不同成分
- 碳质还原剂是铁合金还原电炉应用最()最()的还原剂。广泛;廉价
- 还原剂过剩或不足,都会恶化炉况,使()增加,()降低。诺兰达炉的冰铜品位一般控制在()。电耗;硅回收率A、50%以下
B、50-60%
C、60-65%
D、65-73%#
- 电极糊的粘结材料有()和()。硫酸铜晶体分子式为()属于侧吹熔池熔炼的熔炼工艺是()。沥青;焦油A、CuSO4
B、CuSO4.5H2O#
C、CuSO4.H2O
D、CuSO4.3H2OA、艾萨炼铜法
B、三菱炼铜法
C、闪速熔炼
D、诺兰达法#
- 铁水浇铸时应控制适当的浇铸()和()浇铸。温度;速度
- 温度低时各种氧化物的分解压低,且各氧化物之间的()大。分解压差
- 自焙电极因()、(),因此被广泛用于铁合金生产。工艺简单;成本低
- 炉用变压器的冷却方式一般()和()两种。自然冷却;强制冷却
- 氧化物的还原度之差越大,还原剂分配上的差别也()。对于高熔点物质,在配料中应控制低于()。越大0.5%
1%#
1.1%
2%
- 用碳作还原剂时,反应物除金属元素外,就是一氧化碳气体,一氧化碳气体易于从反应区(),所以反应进行的比较()。排出;完全