查看所有试题
- 一般光缆的标准出厂盘长为()。不属于用户引入线维护的主要内容()A、200米
B、2公里#
C、4公里保持支撑件牢固、绑扎合格,无托、磨现象,无市电侵入危险
检查架空用户引入线的完好和垂度
室内布线应安全、牢固、隐
- 工程维护材料管理中,当维护料存量低于规定最高库存量的()则要及时补充。下列哪块单板不属于M820监控子系统?()单个SDH622M环网不能采用()作为保护方式。A.20%B.30%C.40%D.50%SNP
SOSC
SEI
ODU#二纤通道保护环
- OSN1500的AUX板完成的功能有()。浸油木杆及水泥杆路大修周期()提供单板间LANSWITCH通信通路#
为系统提供3.3V备份电源#
完成系统两路独立-48V电源的监控#
处理公务开销字节8-10年
5-8年
10-15年#
- 全塑电缆对高电压的防护,下面哪些是常用的防护措施。()A、改变电缆线路的路由。#
B、选用塑料护套外加双层钢带绉纹纵包铠装聚乙烯护层的电缆,提高电磁屏蔽性能。#
C、加装气体放电管。#
D、严重危险影响地区应在同
- 每月应对代维单位的服务水平、故障处理能力和()进行考核评比。S320G系统中,以下的配置限制描述错误的是()。A.网络质量#
B.维护质量
C.业务能力
D.技术配置ALC功能时必需配置73SCC;
配置通道保护功能必需配
- 正确的光缆线路施工准备的工序是()。管道光缆引上至架空敷设时,应采取穿()保护,并穿放子管。A、路由复测—光缆单盘检验—光缆配盘—路由准备;#
B、路由复测—光缆单盘检验—光缆长度复测—光缆配盘;
C、查勘—路由复
- 启动T2000工作站时,下列描述正确的是()。开机前,检查工作站的电源线、显示器的电源线、显示器的数据线是否已正确连接,工作站的以太网线是否已连接到集线器。#
如果有外接设备如打印机、调制解调器等,请检查打印机
- 维护有时需要多次清洁光纤,应使用()。光缆发生障碍后应()。A.酒精
B.清洁纸
C.清洁剂
D.专用的光纤清洁器#可暂缓处理
等待上级领导安排
发现防碍立即抢修#
- 在M820开局时,合并VLAN后telnet到SNP192.168.1.4,需要添加端口号?()OTDR屏幕上显示的曲线是()。23
9023#
21
80前向散射曲线
背向散射曲线#
散射曲线
- STM-N的帧结构由哪三部分组成?()段开销、管理单元指针、信息净负荷#
再生段开销、复用段开销、信息净负荷
段开销、通道开销、信息净负荷
通道开销、管理单元指针、信息净负荷
- SOTU10G间接调制色散容限值为多少?()光缆沿室内楼层凸出墙面的挂镜线敷设时,卡钩距离为()米。3200ps/nm
12800ps/nm
800ps/nm#
400ps/nmA
- SOSC单板有4个电口,4个光口,其中电口2是用于()。网管的默认网关
SNP的网关#
电监控通道
光监控通道
- 大宗物资实行公司()制度,保障维护生产用料的质量和供应的及时性,控制维护成本。以下仪表具有电路监听功能的是()。根据传输性能、距离和用途,光缆可分为()。A.自主采购
B.分散采购
C.集中采购#
D.分批采购O
- 光缆在施工敷设时,弯曲半径应大于光缆外径()在传输设备日常维护中,需要两周进行一次的维护项目()。以下有关OptiX2500+子架SDH电接口和转接板的搭配是错误的为()。A、15倍
B、20倍#
C、25倍
D、30倍设备风扇状
- 下列那些情况可能导致TWC产生RLOS告警()。光纤断#
光纤衰减过大#
SCC损坏
TWC接头松动#
- 维护故障处理中,网管操作常用的操作有()。传输电子办公支撑系统有哪些?()把光信号变换成电信号的器件称之为光电检测器件。光纤通信中使用的半导体光电检测器有()环回#
主备倒换#
单板复位#
单板替换传输室电
- 华为公司OptiX155/622设备不能提供的网管接口有()。F&f
576k#
ETHERNET以太网双绞线
X.25
- 关于M820合并VLAN和分离VLAN的说法,正确的是()。设备监测到FANFAIL告警时最不可能的原因是()。合并VLAN是为了隔离内部IP,外部不可见
分离VLAN是为了隔离内部IP,外部不可见#
通过SPWA单板上TST键合并或者分离VLAN