查看所有试题
- 基本的精馏装置包括()①精馏塔;②塔底再沸器;③汽化器;④冷凝器蒸馏塔顶二氧化碳气流入下道工序时,若管道上的孔板流量计测量值为7000NM3/h,则其质量流量约为()A、①②③
B、①②④#
C、①③④
D、②③④A、12000Kg/h
B、14000
- 介质在()换热器内换热时,发生传质过程。如果吸附塔内只有氧化铁脱硫剂和水解催化剂各一层填料,那含有H2S和COS的二氧化碳气流经过的顺序应为()A、直接接触式#
B、间壁式
C、蓄热式
D、间歇式A、先经过氧化铁脱硫
- 脱硫塔的填料床层要在一定的温度下才能工作,主要原因是()的转化反应。由气缸、进排气阀、活塞等部分组成的为()A、H2S
B、COS#
C、单质S
D、SO2A、压缩机构#
B、传动机构
C、润滑系统
D、工作机构
- 由于某种原因,导致液体充满塔板之间的空间,使塔的正常操作受到破坏,这种现象称为()()用于连接分散处理单元、工程师站、操作员站等,完成各站的通讯和数据交换。A、雾沫夹带
B、漏液
C、液泛#
D、返混A、系统网络
- 管式换热器中,应用最为广泛的是()A、沉浸式蛇管换热器
B、喷淋式换热器
C、套管式换热器
D、列管式换热器#
- 食品级二氧化碳提纯装置中,催化反应产物为()二氧化碳提纯装置中,提馏工序的主要目的是分离()A、H2O和CO2#
B、H2O
C、CO2
D、CH4A、油
B、水
C、氢、甲烷、氮、氧等不凝性气体#
D、C2H6
- 吸附塔再生操作,应()A、升温平稳,降温迅速
B、升温迅速,降温平稳
C、到达再生温度时应停留一定时间以保证再生充分#
D、无需气流吹扫
- 二氧化碳提纯装置中,提馏工序的主要目的是分离()准确地表达物体形状、尺寸及其技术要求的图为()A、油
B、水
C、氢、甲烷、氮、氧等不凝性气体#
D、C2H6A、图示
B、草图
C、图样#
D、零件图
- 填料塔中,蒸汽与液体相接触进行热量和物质的交换主要是在填料表面进行的,因此填料的性能直接影响着填料塔的性能。下列关于填料的说法不正确的是()A、填料的比表面应大,以保证气液接触良好
B、填料的自由体积(是指
- 二氧化碳提纯装置中的高温管道常用岩棉保温,是因为()A、强化传热
B、岩棉导热系数相对较小#
C、隔绝空气,减少腐蚀
D、岩棉的空隙率大,含有空气多,导热系数增大
- 关于烃类在催化反应塔内的燃烧过程,下列说法正确的是()下面哪一点是符合屏蔽泵的运转要求的()A、生成产物形成了新的杂质
B、长的碳链更容易断裂,而双键的碳链较单键碳链稳定
C、反应需在一定的温度下才能进行,故
- 变温吸附是工业上使用较多的一种操作方式,变温吸附是指()CRT上部有报警区,点击()可以确认最新报警区的两条最新报警。A、吸附过程温度升高
B、吸附过程温度降低
C、在较低温度下进行吸附,在较高温度下脱附#
D、吸
- 关于平衡蒸馏和简单蒸馏,说法不正确的是()CO2气在经过吸附床层时会有一定的压降,如果压降逐渐变大,不可能的原因是()。A、都是单级蒸馏操作
B、都是仅进行一次部分气化和部分冷凝的过程
C、都是部分地分离液体混
- CRT中部工艺流程图区,测点的颜色随状态变化,若测点红色闪光表示()A、高报警且未确认#
B、高报警且已确认
C、低报警且未确认
D、低报警且已确认
- 蒸馏塔自下而上应有较小的压力降,如生产过程中发现压降偏大,可能的原因是()。①回流过大②填料层脏③气速过快④壁流效应离心泵结构部件中起封闭泵壳与泵轴之间的空隙作用的是()A、①②
B、②③
C、②③④
D、①②③#A、导向环
- 我国规定在特别危险的场所的安全电压是()。A、24V
B、12V#
C、60V
D、36V
- 关于二氧化碳的分子结构,说法不正确的是()调节阀的控制面板上,“输出值”表示()A、分子为线性对称结构
B、构造式为O=C=O
C、是双键结构
D、分子结构很不稳定#A、现场参数的实际值
B、参数的目标值
C、对现场调节阀
- 在不超过二氧化碳临界温度的前提下,通过()方法,可以使用气态二氧化碳液化。A、加压
B、降温
C、加压和降温#
D、减压
- 关于精馏操作,下列说法不正确的是()压缩机工作过程中,当活塞由外止点向内止点开始移动时()A、塔顶馏出的是易挥发组分
B、塔釜馏出的是高沸点组分
C、精馏过程同时存在着传质和传热
D、精馏过程中,轻组分不断从气