查看所有试题
- 在NPN三极管放大电路中,如果集电极与基极短路,则()。装配零、部件、外购件,应使其标记处于便于()。对于指针、标度尺读数装置的误差,根据()可分为视差和结构误差。A、三极管将深度饱和
B、三极管将截止#
C、三
- 电流表的出厂检验项目不包括()。A、升降变差
B、满度误差#
C、偏离零位
D、位置影响
- 光电池是把光能直接转换成()。A、化学能
B、机械能
C、热能
D、电能#
- 图号的作用包括:表示零件、部件的种类、()及索引。对于指针、标度尺读数装置的误差,根据()可分为视差和结构误差。一般的金属或()的电解质都是导体。A、装配要求
B、颜色
C、规格#
D、内部结构A、差值大小
B、
- 在包括电工仪器仪表在内的电气设备中,对()起有效作用的材料称为电工材料。箱壳可由塑料、金属、()等不同材料制成。数字特斯拉计使用时应先接通电源,预热20min左右,然后调零,到数字出现“()”时,即可进行测量。A
- 电缆端头焊接时,芯线与插针间露线不应大于(),插头固定夹必须有良好的固定作用,但不得夹伤电缆绝缘层。只能读出不能写入,但信息可以永久保存的存储器是()。按用途分类,计算机可分()与数据处理机等。A、0.5mm
B
- 下面()不是并联电路的特点。装配前认真消化图纸资料,准备好需用的装配(),整理好工作台。检查装配用的所有材料、机械和电气零部件、外购件是否符合图纸要求。电磁系电压表的波形误差来自于铁心材料非线性的影响及
- 整机测试及出厂检验中出现的不合格应进行返工,返工过程中应首先分清原因,属于零部件、元器件质量问题的应予()。A、修理#
B、重加工
C、更换
D、作废
- 在装配、调整、拆卸过程中,紧、松螺钉应对称,()分步进行,防止装配件变形或破裂。如果晶体二极管的正、反向电阻都很大,则该晶体二极管()。一般的金属或()的电解质都是导体。如图所示是几个常用电气元器件实物的
- 饱和标准电池的内电阻随时间而()。波峰焊焊接时造成焊锡量过少或短路较多的原因是()。A、增大#
B、减少
C、不变A、助焊剂浓度过低或助焊剂浓度过高
B、助焊剂浓度过低和波峰角度不好
C、助焊剂浓度过低和喷嘴雾
- 装配前要认真阅读图纸资料,准备好需要的装配(),整理好工作台。检查装配用的所有材料、机械和电气零部件、外购件是否符合图纸要求。将同一产品型号中各级各类图样集中装订在一起,则成为产品图册。图册的幅面以()
- 某放大器输入电压为10mv时,输出电压为7V;输入电压为15mv时,输出电压为6.5V,则该放大器的电压放大倍数为()。磷砷化镓数码管的工作电压为()。根据GB/T7676-1998的规定,标度尺是一系列的()和数字,通过它们与指示
- 标准电池在正常使用时,短时间(偶然)允许放电电流,一等标准电池不应超过()。为得到表达内部结构的全剖视图,通常可采用的剖切方法有:()、旋转剖、阶梯剖、倾斜剖。0.1μA#
0.5μA
1μAA、单一剖切平面#
B、角度剖
- 产品的检验类别除出厂检验外,还有()和周期检验两类。浸焊又称浸锡,是将锡铅焊料加热熔化以后,再将制件浸入,使制件表面涂覆一层锡的操作过程,一般应用于元器件和()的预处理。A、误差检验
B、绝缘检验
C、环境检验
- 多级放大器引入负反馈后,通频带()。磁电系电流表可分为()量限和多量限两类。按照国家计量检定规程JJG124-93的规定,调校装置中的“电源在半分钟内稳定度应不低于被检表误差限值的()”。不变
比其中任何一级都宽
- 电气测量装置的()部分与大地零电位之间的电位差,称为接地时的对地电压。按照点盘时所作的标记和图样、工艺的规定,完成标度尺中全部分度线和分度数字的绘制,这一过程称为()。A、接地#
B、带电
C、工作A、刻盘
B、
- 某仪表等级为1.0其满刻度相对误差为()。施加一个反向的磁场,则永久磁铁的磁通密度必然减小,这种把永久磁铁磁通密度从()减小的物理过程称为退磁。磁电系电流表可分为()量限和多量限两类。1.0%
-1.0%
±1.0%#
±10
- 组成脉冲波形变换电路的基础是()。对已判断为损坏的元器件,可先行将引线(),再行拆除。这样可减少其他损伤的可能性,保护印刷电路板上的焊盘。为确保电子产品有良好的一致性、通用性和()而制定工艺标准。图册明
- 连接导线在装配工作开始前应进行包括切段、清除绝缘、芯线端头搪锡、()等一系列准备工作。在电磁系仪表中,波形误差是由铁心材料的磁化曲线非线性、()以及与频率有关的阻抗引起的。A、弯形#
B、打磨
C、焊接
D、
- 低频信号发生器的输出阻抗()。焊接点区域加温时,一般元器件的焊接时间为3秒,场效应管、MOS等电路等控制在(),接线柱、插头、插座、钮子开关、波段开关、焊片等可控制在3–5秒。整机安装的基本要求:保证导通与绝缘
- 凡是装配好的整、部件和整机都要进行(),要求元器件排列整齐,不能相互碰撞,导线走线合理,不能有拉紧和过长现象。装配后要按照技术要求,对照()对整机逐项进行检查,还需要进行一系列的调校、检测、老化、封盖和检验
- 连接导线在装配工作开始前应进行包括切段、清除绝缘、芯线端头搪锡、()等一系列准备工作。A、弯形#
B、打磨
C、焊接
D、打蜡
- 运行中的电压互感器二次测严禁()。正确识读总装配图的方法是按照总装配图→部件装配图→()图→部件装配图→总装配图的顺序反复进行。根据GB/T7676-1998的规定,标度尺是一系列的()和数字,通过它们与指示器结合,可得
- 射极输出器属()负反馈。()是电工仪器仪表装配的主要依据。电容器按介质材料不同可分为()电容器、空气电容器、云母电容器、瓷介电容器、玻璃电容器和涤纶电容器等。电压并联
电压串联
电流并联
电流串联#A、装
- 低频信号发生器的输出阻抗()。下面()不是并联电路的特点。在装配前对零部件进行清理和清洗,是装配前()的措施。高
低#
不确定A、加在各并联支路两端的电压相等
B、电路内的总电流等于各分支电路的电流之和
C、
- 在NPN三极管放大电路中,如果集电极与基极短路,则()。导线线缆焊接时,芯线与插针间露线不应大于()。电力系统的中性点接地属于()。A、三极管将深度饱和
B、三极管将截止#
C、三极管的集电结将是正偏A、1.2mm
B、