查看所有试题
- 下列关于变压器套管在安装前检查项目描叙正确的是()多台电动机的公用熔丝的额定电流,是按()继电器按其结构形式分类,目前主要有()瓷套表面有无裂纹伤痕#
套管经试验是否合格#
充油套管的油位指示是否正常,有无
- 三相五芯式电压互感器的铁芯是为了便于()磁通通过。关于发电机纵差与横差保护的论述正确的是()零序#
负序
正序
以上均可纵差主要保护相间短路#
横差保护反应匝间故障#
纵差和横差不能相互代替#
横差保护时期有死
- 异步电动机降压启动的方法有()在保护检验工作完毕后、投入出口压板之前,通常用万用表测量跳闸压板电位,正确的状态应该是(直流系统为220V)()定子回路串电抗器启动#
Y-△换接启动#
自耦变压器降压启动#
延边三角
- 对于基建投产设备在投入运行的头三年内,应每()年进行一次定期检验。电力变压器的油起()作用。一#
二
半年绝缘#
防锈
冷却#
灭弧
- 电机铁心常采用硅钢片叠装而成,是为了()便于运输
节省材料
减少铁心损耗#
增加机械强度
- 在定子绕组引出线或中性点附近相间短路时,两中性点连线中的电流较小,横差保护可能不动作,出现死区范围可达(),因此不能取代纵差保护。检修母线时,应根据()等实际情况确定地线数量。15%~20%#
10%~15%
5%~1
- 防止发电机损坏事故的措施有()防止因定子绕组端部松动而引起的相间短路#
防止定子绕组相间短路#
防止转子匝间短路#
防止发电机非全相运行#
- 那些是检查和处理高压断路器发生跳闸失灵的电气回路故障()为了人身和设备安全,互感器的二次侧必须实行()检查电源电压是否过低,使分闸铁芯的冲力不足或本身低电压分闸值不合格#
检查分闸回路中熔断器或其它动作元
- 当电流互感器不满足10%误差要求时,可采取()措施。继电保护是以常见运行方式为主来进行整定计算和灵敏度校核的所谓常见运行方式是指()增大二次电缆截面#
将同名相两组电流互感器二次绕组串联#
改用饱和倍数较高的
- 转子发生一点接地仍可以继续运行的危害()电动机外壳带电,可能的原因有()交流接触器接在与它额定电压相等的直流电源上,交流接触器将()发展为两点接地故障#
分转子绕组发热,有可能被烧毁#
电机转子由于作用力偏
- 电阻限流有载调压分接开关有哪几部分组成()切换开关#
选择开关#
范围开关#
操动机构#
- 接地网的接地电阻一般应不大于()0.5Ω#
0.4Ω
0.1Ω
5&Omega
- 运行中的电流互感器可能出现()异常现象两相变压器间定相是为了核定()是否一致。二次侧开路#
过热#
螺丝松动#
运行声音异常#相序
相别
相位#
相序和相位
- 常用的减少接触电阻的方法有()模拟型方向阻抗继电器受电网频率变化影响较大的回路是()用2500V摇表测量真空灭弧室的断口绝缘,一般不应低于()磨光接触面,扩大接触面#
加大接触部分压力,保证可靠接触#
涂抹导电膏
- 110KV充油电力设备在注油后应静置()h才可进行耐压试验。48
24#
12
72
- 在母线电流差动保护中,为防止()继电器误动作或误碰出口中间继电器造成母线保护误动作,故采用电压闭锁元件接入重合闸不灵敏一段的保护定值是按躲开()整定的。当变压器二次侧电压随负载增大而升高时,则所带负载为
- 电动机大修后,应做的检查和试验有()当电容器额定电压等于线路额定相电压时,则应接成()并入电网。测量绕组的直流电阻#
绝缘电阻的测量#
耐压试验#
空载试验#串联方式
并联方式
星形#
三角形