查看所有试题
- 流入电路中一个节点的电流之和()流出该节点的电流之和。爆炸危险环境内的电气设备与接地线的连接宜采用(),其铜线最小截面面积不得小于4mm2。电气设备送电方案编写时注意()。A.大于B.小于C.等于D.无关。A、单芯
- 电流的单位名称是()。流入电路中一个节点的电流之和()流出该节点的电流之和。可编程控制器PLC的扫描速度常用()表示。库仑;
伏特;
安培;#
欧姆;大于;
小于;
等于;#
无关;A、ms/千步#
B、s/千步
C、μs/
- 开关量输入、输出系统中抗干扰器件光电耦合器一般由()组成。A、一个光电二极管B、一个光敏三极管C、一个光电二极管和一个光敏三极管D、两个光电二极管
- 电压和电流的关系式I=U/R,这是()。技术论文的写作要求是()。欧姆定律;#
基尔霍夫定律;
电压定律;
电流定律;A、选题恰当B、主旨突出C、叙述全面D、语言准确#
- 人站立或行走在有电流流过的地面时,两脚间所承受的电压称()电压。A.接触B.跨步C.接地D.相同
- 发电机横差保护的不平衡电流主要是()引起的。基波
三次谐波#
五次谐波
高次谐波
- 目视管理是现场5-S管理中()常用的方法。二极管全波整流电路平均值输出电压是二极管半波整流电路的()。在培训教学中,制定培训规划的原则是()。A、常组织B、常整顿C、常自律D、常规范A、10倍B、8倍C、4倍D、2倍A
- 分层管理是现场5-S管理中()常用的方法。中性点不接地系统,一旦发生间歇性单相接地故障,容易产生系统()。A、常清洁B、常整顿C、常组织D、常规范A、过电流B、过负荷C、过脉冲D、过电压
- 三绕组变压器的零序保护是()和保护区外单相接地故障的后备保护。全控桥可控整流工作状态处在()区间为有源逆变工作状态。A.高压侧绕组B.中压侧绕组C.低压侧绕组D.区外相间故障的后备保护#A、0°—90°B、90°—0°C、90
- 设备档案中,原始资料包括()。A、设备制造厂说明书B、安装竣工图纸C、出厂试验记录D、安装记录及试验报告#
- 组成可编程控制器PLC的各部件中,()是故障率较高的部件。氧化锌避雷器试验中()。A、CPU
B、存储器
C、电源部分#
D、输入输出部分A、U1mA实测值与初始值或制造厂规定值比较,变化不应大于±5%B、U1mA实测值与初始值
- 绝缘靴(鞋)的试验周期是()。在ISO9000族标准中,不能作为质量管理体系审核的依据是()。A.每年一次B.每半年一次C.每季度一次D.一个月一次A、质量管理体系文件B、合同C、GB/T19001标准及相关法律法规D、T19004标
- 只有发生(),零序电流才会出现。下列关于短路电流叙述正确的有()A.相间故障B.振荡时C.接地故障或非全相运行时D.短路A、当短路点发生在发电机附近时,三相短路电流一定大于两相短路电流
B、当短路点发生在发电机附
- 凡系新安装或变动过一、二次回路的差动保护,正式投入前须测量(),以检查电流回路接线是否正确。设置在爆炸危险场所的电气设备(包括移动设备),下述()应该接地。A、差电流B、动作时间C、一次电流D、二次电流#A、
- 以下设备需要测量直流电阻的是()。A、电容器B、避雷器C、电动机D、绝缘子
- 凡系新安装或变动过一、二次回路的差动保护,正式投入前须测量(),以检查电流回路接线是否正确。同步电动机自失步到再同步的整个机电暂态过程主要包括以下()阶段。A、差电流B、动作时间C、一次电流D、二次电流#A、
- 爆炸危险环境内的电气设备与接地线的连接宜采用(),其铜线最小截面面积不得小于4mm2。电气系统非同期并列,会导致()。A、单芯线B、多芯线C、元钢D、多股软铜线A、设备爆炸B、系统严重冲击C、主变损伤D、电力系统崩