查看所有试题
- 产生过渡过程的外因是()。变压器过电流保护的灵敏度系数lmK是反映保护的一个重要参数,其决定因素有()。A.电路中有储能元件B.电路断开C.电路关闭D.换路。#A、变压器的接线方式B、保护装置的接线方式C、短路故障的
- 当外加电压降低时,电动机的电磁力矩降低,转差()。蓄电池浮充电运行,如果直流母线电压下降,超过许可范围时则应()恢复电压。A.降低B.增大C.无变化D.有变化。切断部分直流负载;
增加蓄电池投入的个数;
增加浮充电
- 在变电站综合自动化系统中,特别是微机保护、自动装置与监控系统相互通信电路中,主要是使用串行通信。串行通信常采用的物理接口标准有()。电流速断保护不能保护线路的全长,它保护线路的范围的大小与()因素有关。A
- 电流的单位名称是()。库仑;
伏特;
安培;#
欧姆;
- 高压并联电容器并联电阻值与出厂值的偏差应在()范围内。变压器垫料缝渗漏油的原因是()。A、2%B、5%C、10%D、15%A、螺丝和压盖接触不紧密B、垫料不良,需要更换C、结合面不干净有油污D、结合面有锈垢#
- 对已有单独试验记录的若干不同试验电压的电力设备,在单独试验有困难时,可以连在一起进行耐压试验。此时,试验电压应采用所连接设备中试验电压的()。A、最高值B、最低值C、最高值与最低值之和的平均值D、各试验电压
- 电力系统的内部过电压的倍数规定为内部过电压幅值与其电网工频相电压的()之比值。A、有效值B、幅值C、平均值D、最大值#
- 在企业培训中,最基本的培训方法是()。以二极管半波单相整流电路而言,输入110V有效值电压,则输出平均值电压约为()V。A、讲授法B、专题讲座法C、研讨法D、参观法#A、49#
B、39
C、59
D、79
- 电缆敷设到拐弯处,操作人员应站在电缆()进行操作。A、上方B、下方C、内侧D、外侧
- 同步电动机可以采用()的运行方式,在电网中改善电网的功率因数和减小电网电压波动做调相机使用。新建架空线路运行前,需在额定电压下,对空载线路进行()次合闸试验,带电运行72h。A、欠励B、欠复励C、过励D、复励A、
- 人站立或行走在有电流流过的地面时,两脚间所承受的电压称()电压。A.接触B.跨步C.接地D.相同
- 发电机变为同步电动机运行时,最主要的是对()造成危害。A.发电机本身B.电力系统C.汽轮机尾部的叶片D.汽机大轴。
- 锅炉所有水位计损坏时应()。充油电力设备在注油后需静置一定时间才进行耐压试验,以下正确的是()。A、紧急停炉B、申请停炉C、继续运行D、通知检修#A、500kV设备静置时间大于72hB、220kV设备静置时间大于48hC、110
- 避雷器间隙的击穿电压比被保护设备绝缘的击穿电压()。A、高B、稍高C、相等D、低
- 一变电所进线电流为55A,当需要投上无功补偿电容器时,高压无功补偿电容器工作电流5A,进线电流与以下()接近。A、45B、50C、60D、65
- 电气安全技术规范规定:保护零线(PE线)必须用()的专用线。A、黄色
B、黄绿双色#
C、红黄双色
D、蓝色
- 试品残余电荷对泄漏电流测量结果的影响是()。A、结果偏大B、结果偏小C、结果偏大或偏小D、结果不变
- 由直流双臂电桥的结构原理可知,为了减小接线电阻和接触电阻的影响,要求双臂电桥四个桥臂上的标准电阻均不小于()Ω。A、0.1
B、1
C、10#
D、100