查看所有试题
- 用户程序通过编程器写入主机的()。A、系统程序存储器
B、RAM或EPROM#
C、中央处理单元
D、寄存器
- 常用的灭狐方法有()。电动机是滑动轴承的位号有()A、把电弧沿其轴线拉长#
B、让电弧在磁场的作用下拉长#
C、借窄缝效应使电弧迅速冷却#
D、利用栅片把电弧分成串联的短电弧#
E、利用多断点把电弧分成串联的几段#
- 晶闸管—电动机系统的可逆线路可采用()可逆方式。A、电阻
B、电容
C、电抗
D、励磁#
- 设置中间继电器的目的是()。A、接触器触点容量不足
B、增加控制信号,提高控制可靠性
C、用继电器代替行程开关
D、将重复程序特征码区分开来#
- 下面那些油浸变压器主要部件()铁芯#
绕组#
油箱#
油枕#
呼吸器#
- 206工号电动葫芦的控制电源为()A、AC220V
B、AC42V#
C、AC24V
D、DC110V
- 基本单元的接地()同期重合闸在那些情况下不动作()用1mm2以上的电线,实行第二种接地
用2mm2以上的电线,实行第三种接地#
应与强电系统接地共用
不能与扩展单元的接地端互相接地线路发生永久性故障#
无压重合闸拒动
- C301氨压机一次最长启动时间和连续多次启动时间总和不超过()2C510、2C540电机的防爆类型为()A、1分钟
B、2分钟#
C、3分钟A、隔爆型
B、增安型
C、本安型
D、正压通风型#
- 以下关于交流负反馈的说法错误的是()使用的空气开关优点主要有()乙炔配电室的电源种类有()能稳定取样对象
能稳定静态工作点#
串联负反馈能提高输入电阻
电压负反馈能减小输出电阻A、灭弧能力强#
B、能带负荷通
- 三相同步变压器的相序接错,不会发生()的情况整流输出电压正常#
整流输出电压缺相
无整流输出电压
触发电路工作正常
- 转速负反馈无静差调速系统中转速调速器采用()。用开启边界线的转换主令信号作()。A、比例调节器
B、比例积分调节器#
C、微分调节器
D、调节器A、关断主令信号
B、开启主令信号#
C、开启约束条件
D、关断约束条件
- 电缆通过不均匀沉降的回填土地段受力较大的场所时,不宜采用以下哪一种敷设?()直埋;#
穿钢管;
穿混凝土管;#
穿可挠性塑料管。#
- 在深度负反馈条件下,串联负反馈电路的()晶闸管—电动机系统的主回路电流断续时,开环机械特性()。输入电压与反馈电压近似相等#
输入电流与负反馈电流近似相等
反馈电压等于输出电压
反馈电流等于输出电流A、变软#
- 测量电枢整流片间直流电阻,相互间的差值不应超过()。A、10%
B、5%
C、2%#
- 在晶闸管组成的直流可逆调速系统中,为使系统正常工作,其最小逆变角βmin一般选()有哪些原因会造成开关拒绝跳闸。()A.60度
B.45度
C.30度#
D.15度母线接地
操作回路不通#
合闸铁芯未返回#
电机所带机械部分严
- 用SQ与两触点串联去控制一个继电器线圈,在()时,继电器线圈为受激状态。所谓换路是指电路的()等,使电路中的能量发生变化,但这种变化是不能跃变的。A、SQ=1,KM=1
B、SQ=1,KM=0#
C、SQ=0,KM=1
D、SQ=0,KM=0A、电流