查看所有试题
- 未取得计量检定员证件执行计量检定的,以及使用未经考核合格的计量标准开展检定的,若未构成犯罪,应给予()行政处罚
行政处分并处以罚款#
通报批评
500元以下罚款
- 用兆欧表进行测量时,应使摇动转速尽量接近()。在现场测定电能表基本误差时,若负载电流低于被检电能表的基本电流的()时,不宜进行误差测量。A、60r/min
B、90r/min
C、120r/min#
D、150r/min1/2
1/3#
1/4
1/5
- 关于有功功率和无功功率,正确的说法是()。无功功率就是无用的功率
无功功率有正有负#
在RLC电路中,有功功率就是在电阻上消耗的功率#
在纯电感电路中,无功功率的最大值等于电路电压和电流的乘积#
- 用0.1级的电流互感器作标准,检定0.5级电流互感器时,在额定电流的100%下,比差和角差的读数平均值分别为-0.355%、+15′。已知标准器的误差分别为-0.04%′、+3.0′,则在检定证书上填写的比差和角差应分别为()。-0.35%、+
- 电能表的工作频率改变时,对()。A、相角误差影响大#
B、幅值误差影响较大
C、对相角误差和幅值误差有相同影响
D、对相角误差和幅值误差都没有影响
- 违反本法第四十九条第二款规定,()由电力管理部门责令改正;情节严重的,对有关主管人员和直接责任人员给予行政处分;造成损失的,责令赔偿损失。A、不能保证农业和农村用电的合适比例
B、没有优先安排农业排涝、抗旱
- 用户反映电能表跑快,经校验误差为+3%,电能表为2.0级表,应退电量()。一般对于周期检定的电子式标准电能表,可通过测试绝缘电阻来确定电表绝缘性能,测量输入端子和辅助电源端子对外壳,输入端子对辅助电源端子之间的绝
- 用三相两元件电能表计量三相四线制电路有功电能,将()。A、多计量
B、少计量
C、正确计量
D、不能确定多计或少计#
- 下面有几个计量误差的定义,其中国际通用定义是()。为使测量更准确,测量9V电压时,应选用以下哪个量限的电压表:()A、含有误差的量值与其真值之差#
B、计量器具的示值与实际值之差
C、计量结果减去被计量的(约定
- 一只进口表的常数是C=720Ws/r,它相当于()r/kWh。A、5000#
B、720000
C、2592
D、2000
- 电流互感器二次阻抗折合一次侧后,应乘()倍(电流互感器的变比为K)。实践证明,()是清洗计度器支架、圆盘和铝质零件最理想的洗涤剂。1/(K*K)#
1/K
K*K
K白汽油
苛性钠溶液
混合液#
苛性钠混合液
- 使用电压互感器时应注意的事项()。使用前应进行检查#
二次侧应保护接地#
运行中二次绕组不允许开路
运行中二次绕组不允许短路#
- 电能表的工作频率改变时,对()。标准装置首次检定后1年进行第一次后续检定,此后后续检定的检定周期为()年。A、相角误差影响大#
B、幅值误差影响较大
C、对相角误差和幅值误差有相同影响
D、对相角误差和幅值误差