查看所有试题
- 应()的设备[断路器(开关)、隔离开关(刀闸)、接地刀闸等],验电,装拆接地线,安装或拆除控制回路或电压互感器回路的熔断器,切换保护回路和自动化装置及检验是否确无电压等项目应填入操作票内;拉开;
拉合;#
合
- 经本单位批准允许单独巡视高压设备的人员巡视高压设备时,不得进行其他工作,不得移开或越过()。临时遮拦;
固定遮拦;
遮拦;#
警戒线
- 工作场所的照明,应该保证()。进行停、送电操作时,在拉、合隔离开关(刀闸),手车式开关拉出、推人前,检查()确在分闸位置项目应填入操作票内;电缆直埋敷设施工前应先查清图纸,再开挖足够数量的样洞和样沟,摸清地
- 接地线应使用()固定在导体上,严禁用缠绕的方法进行接地或短路。专用的线夹;#
焊接;
铆接;
螺栓
- 在同一变电站或发电厂升压站内,依次进行的()的带电作业可以使用一张带电作业工作票。不同类型;
同一类型;#
相同类型;
同一电压等级
- 等电位作业人员在绝缘梯上作业或者沿()进人强电场时,其与接地体和带电体两部分间隙所组成的组合间隙不得小于表6-5的规定。导线;
绝缘梯;#
绝缘子串;
绝缘绳
- 应()的设备[断路器(开关)、隔离开关(刀闸)、接地刀闸等],验电,装拆接地线,安装或拆除控制回路或电压互感器回路的熔断器,切换保护回路和自动化装置及检验是否确无电压等项目应填入操作票内;拉开;
拉合;#
合
- 进入作业现场应将使用的带电作业工具放置在()的帆布或绝缘垫上,防止绝缘工具在使用中脏污和受潮。试验装置的电源开关,应使用明显断开的()。为了防止误合刀闸,可在刀刃上加绝缘罩。防静电;
防潮;#
防污;
绝缘
- 在未做好()的情况下,不准登在不坚固的结构上(如彩钢板屋顶)进行工作。加固;
支撑;
安全措施;#
安全防护
- 在()与短路端子之间导线上进行任何工作,应有严格的安全措施,并填用“二次工作安全措施票”。必要时申请停用有关保护装置、安全自动装置或自动化监控系统。互感器;
电流互感器;#
电压互感器;
二次回路上
- 在连续档距的导、地线上挂梯(或飞车)时,其导、地线的截面不得小于:钢芯铝绞线和铝合金绞线()mm2;钢绞线50mm2(等同0PGW光缆和配套的LGJ-70/40导线)。75;
120;#
150;
110