查看所有试题
- 并励直流电动机降低电枢电压起动()通过改变转差率来实现调速的方法是()。起动转矩减小#
增加起动转矩
增加主磁通
减少起动时间改变电源频率
改变磁极对数
在转子电路中串接电阻#
改变电源电压
- 直流电机的主磁极线圈套入铁心后,耐压试验电压应为()伏。2.5UN+2500#
2.5UN+1900
2.5UN+1700
2.5UN+1000
- 直流牵引电动机当转速随转矩发生变化时()基本不变。与电磁噪声有关的因素有()YBX中的X代表()输入电流
输出功率#
输出转矩槽配合#
槽斜度#
铁心装压质量#
气隙均匀度#
轴承的装配质量
电机的结构刚度。#机座长
- 一台2P=4的单叠绕组若有一个元件断线,则输出电流为原来的()。1/4
1/2
3/4#
1倍
- YBX中的X代表()机座长
高效电机#
高压电机
低压电机
- 电机工作制有()连续运行工作制#
断续运行工作制#
长期工作制
短时运行#
- 串励直流电动机若空载运行则会发生()现象。移出剖面图的轮廓线用()线绘制。与电磁噪声有关的因素有()飞车#
停车
因电流极大冒烟
因转矩极小而拖不动负载粗实#
细实
局部槽配合#
槽斜度#
铁心装压质量#
气隙均
- 为了获得较大的起动转矩,通常规定,直流电动机的启动电流不得大于其额定电流的()倍。直流牵引电动机当转速随转矩发生变化时()基本不变。换向器两端燕尾同轴度属于()。1~2倍
1.5~2.5倍#
2~3倍
3~5倍输入电流
- 一台4极直流电机,采用单叠绕组.若去掉相邻的两组电刷,则输出功率()。减小1/2#
减小1/4
减小1/3
增大1/4
- 直流牵引电机换向片的含银量一般为()%。0.01~0.07
0.08~0.15#
0.15~0.23
0.23~0.3
- 电源的端电压U与输出电流I之间的关系为()。使用感应加热器,进行退轴承和套油封作业时,首先应认真仔细地检查感应加热器及联线的绝缘状态是否良好,并正确使用防烫工具和个人防护用品,以免被电击伤和()。U=E-Ir#
- 直流发电机的空载损耗主要与()有关。电枢电流的大小
励磁电流的大小
电枢转速的高低#
- 对绕制好的电机线圈,应检查()符合要求后方可进行嵌线。产生电机空载电流大的主要原因有()尺寸、焊点、导线
材料、尺寸、直流电阻
尺寸、匝数、直流电阻#
匝数、焊点、导线定子内径大#
转子外径大#
定转子铁心窜
- 换向极同心度偏差过大时()。若将Y接的电动机误接成Δ时,电动机空载电流将()。立井提升设备通过()装置进行上下提升运输。换向极磁场不对称
换向极磁场不对称,影响换向#
各支路电势不平衡
电机转速不稳定减小
增
- 草图上的竖线()连续画出。节点电压法就是以节点电压为未知量,求出节点电压,再根据()定律分别求出各支路电流。自下而上
自上而下#
随便方向欧姆定律#
楞次定律
法拉第电磁感应定律
戴维南定理
- 若串励直流电动机的负载发生变化,则()变化很大。端电压
转速n#
效率η
功率p
- 气动扳手气动前在进气口注入少量润滑油()运转几秒钟后,再加()。A.高气压#
B.低气压
C.中气压
D.频繁起动#
- 当电动机的绕组为三角形接法时,发生单相运行()绕组烧坏的可能性最大。三相
二相
一相#
- 移出剖面图的轮廓线用()线绘制。无纬带绑扎与无磁钢丝绑扎相比()。真空压力浸漆设备中冷凝器的作用是()。粗实#
细实
局部效果相同
可以减少涡流损耗#
电气强度强度差
机械强度好降低输漆过程中的漆温
降低回漆
- 直流电机电气火花的特征是()。直流电机的主磁极线圈套入铁心后,耐压试验电压应为()伏。火花呈白色或兰色,连续、稳定、细小,在后刷边燃烧#
火花呈红色或黄色,断续、不稳定、较粗
火花呈白色或兰色,连续、稳定、细