查看所有试题
- 胎模锻造的操作动作应()。缓慢
较慢#
迅速
慢打
- 模锻件上凡是()的部位,都应留有机械加工余量,余量的大小取决于机械加工的要求和模锻工艺所能达到的锻件公差大小。某厂需要生产80000件外圆φ12、内径φ6.5的同轴度要求较高的垫圈,应选用的模具是()黑皮
机械加工#
- 材料的强度常用材料单位面积上的抗拉力来表示,称为()由于摩擦力的存在,必须增加外力来克服它对金属变形的阻力,因而摩擦会增加金属的()内力
应力#
切应力残余应力
锻造温度
变形杭力#
附加应力
- 锁扣作用是防止锻模在模锻过程中产生()。在生产过程中因故停锤使生产间断()小时以上时,在恢复工作前也必须重新预热锻模和锤杆。折伤
错移#
裂纹
断裂1
2#
3
4
- 在零件尺寸加上粗加工和精加工余量后的尺寸,叫做锻件()。最大尺寸
最小尺寸
平均尺寸
基本尺寸#
- 热压模压力机模架内的垫板是为保持上、下模板的()而设置的,垫板直接和模板接触,承受变形时全部压力,是定期更换的零件。长期使用#
临时使用
安全
平行
- 把锻件先进行淬火,然后进行高温回火的热处理工艺叫做调质,目的是提高()。锻件的强度
锻件的硬度
综合力学性能#
- 在晶体内,原字按一定几何规律在空间排列成所谓的结晶构架,叫做()。锻件的外观检验不包括下列中的()晶面
晶粒
晶格#折叠
裂纹
过烧#
错移
- 模锻通常按所用()和锻模结构进行分类。钛合金在900℃以下锻造,()受变形速度影响较大;在900℃以上则无明显的影响,在压力机和锤上均可锻造。模锻设备#
模锻工具
模锻材料
加热温度抗变强度
变形强度
工艺塑性#
- 每种下料方法都有其显著特点,锯切下料显著特点是()。尺寸精度高#
生产效率高
端面质量差
无金属损耗
- 将锻坯拔长、扁方使其砧宽比提高,以达到()的目的的锻造方法,叫做SUF法,又叫正扁方法。锻合内部缺陷#
防止内部产生裂纹
防止产生折叠
- 需设计热锻件图的锻件一般是()。在金属的塑性变形分类中,其变形抗力最大的是()。摸锻件、胎膜件,特别是合摸成形件#
自由锻件
黑皮锻件
机架工件弹性变形
冷变形#
温变形
热变形
- 为了方便制造锻模,热锻件图上的高度应尽量注在()模具底部
分模面上#
锻件的基准线上
- 在晶体内,原子按一定几何规律在空间排列成所谓的结晶构架,叫做()。加工硬化后的金属处于不稳定状态,虽然有转化为稳定状态的趋势,但在常温下由于()很微弱,而无法恢复到稳定状态,只有提高金属温度来增加原子的活动
- 锻件图有冷、热之分,通常冷锻件图是生产检验时的主要依据,热锻件图是()。一定断面尺寸的钢材,加热开裂的原因除它的化学成分、导热性、装炉温度等有关外,还有一个重要的原因是()坯料尺寸确定
模具设计制造#
机械
- 标有尺寸公式又画有零件轮廓线的锻件图称为()。冷锻件图#
热锻件图
模具图
零件图
- 液压油的物理性质与()无关。冷锻件图只能使用于()密度
粘度
压缩性
温度#制造模具
设计模具
锻件的检测#
模具检测