查看所有试题
- 某矿提升机深度指示器为机械牌坊式,在正常运行过程中突然出现传动轴连接销脱落而主提升机操作工并未发现,发生这样的事情可能导致的后果有()。绞车自动停止
正常工作
自整角机运转
发生过卷#
- 提升机设置的托罐装置,必须能够将撞击防撞梁后再下落的容器或配重托住,并保证其下落的距离不超过()。调绳离合器主要用于()使两滚筒之间产生相对转动。O.5m#
1.0m
1.5m
2.0mA、制动系统
B、换钢丝绳#
C、卷筒与主
- 微拖动装置的机械传动系统包括()。主提升机紧固件必须满足()。A、气囊离合器#
B、球面蜗杆减速器#
C、微拖动电动机#
D、储气罐#
E、进气#A、螺纹无乱扣#
B、稳钉与稳钉孔吻合#
C、铆钉必须紧固#
D、键不松旷#
E
- 电液调压装置为实现()等能量的精确转换,应注意十字弹簧与控制杆之间相互固定的位置关系。A、电#
B、磁#
C、机械#
D、液压#
E、气压
- “一坡三挡”中的上部挡车栏设在变坡点下方()处。10m
15m
略大于一列车长度的地点#
20m
- 主轴方面的通用部件有()。大修后的试运转步骤包括()。A、各紧固件#
B、键和键槽#
C、轴和轴承#
D、联轴器#
E、基础、油漆#A、空运转#
B、无负荷试运转#
C、带负荷试运转#
D、装设备
E、刷油漆
- 多绳提升宜采用()。提升机操作工的岗位责任制中提到的“五严”是指严梏执行()。交互捻钢丝绳
同向捻钢丝绳
对称左右捻钢丝绳#
左右捻钢丝绳A、交接班制度#
B、操作规程#
C、要害场所管理制度#
D、巡回检查#
E、岗
- 提升机制动力矩过小可能发生()事故可能发生跑车事故#
造成断绳事故
可能使连接装置承受过大的冲击力
急停
- 对于摩擦轮式提升绞车的防滑计算,钢丝绳与摩擦轮问摩擦系数的取值不得大于()。通常液压站的残压不得超过()。O.2
0.22
O.25#
0.30.5Mpa#
0.6Mpa
O.8MPa
0.7MPa
- 提升机设置的托罐装置,必须能够将撞击防撞梁后再下落的容器或配重托住,并保证其下落的距离不超过()。斜井提巷除在()停车外,中途停车任何情况都不得松闸。O.5m#
1.0m
1.5m
2.0m领导指示
特别危害
停车场#
上平台
- 矿井提升设备的作用不正确的是()。提升煤炭和矸石
升降人员
升降物料及设备
监测地下环境#
- 煤矿立井大都采用()。普通罐笼和底卸箕斗#
吊桶
后卸式箕斗
矿车
- 深度指示器指示位置不准时,应()。向调度室及领导汇报,等待指示
及时与信号工联系,重新调整#
提高操作注意力,防止过卷或墩罐
- 主轴装置轴承中的润滑脂应()全部更换一次。微拖动装置的机械传动系统包括()。一月
一季度
一年#
不定期A、气囊离合器#
B、球面蜗杆减速器#
C、微拖动电动机#
D、储气罐#
E、进气#
- 某矿主提升电动机启动后进人等速运行阶段时,转速低于额定转速,其转速低的原因是()。电动机过热,通风不良
启动电阻未完全切除#
电动机只有两相在工作
电源开关接触不好
- 提升容器高速运行时,提升机发生保险制动,应()。提升机在运转中出现不明信号时,应采用()进行中途停车。立即停车检查钢丝绳及连接装置#
将容器缓慢送到终点检查钢丝绳及连接器
追究事故责任者的责任
交班后处理保
- 提升机有()等。A、单绳缠绕式#
B、多绳缠绕式#
C、单绳摩擦式#
D、缠绕摩擦式
E、多绳摩擦式#
- 提升绞车的常用闸和保险闸制动时,所产生的力矩和实际提升最大静荷重旋转力矩之比K值不得小于()。对使用中的斜井人车防坠器,应()进行1次手动落闸试验。2.0
2.5
3.0#
4.O每月
每天#
每班
每旬
- 某矿主提升电动机启动后进人等速运行阶段时,转速低于额定转速,其转速低的原因是()。电动机过热,通风不良
启动电阻未完全切除#
电动机只有两相在工作
电源开关接触不好
- 煤矿立井大都采用()。单绳提升的楔形连接装置的累计使用期限不得超过()年。普通罐笼和底卸箕斗#
吊桶
后卸式箕斗
矿车10#
15
20
5
- 开车信号应设有()保留信号。音响
声光
灯光#
开车
- 提升钢丝绳是用来()。在规定的接班主提升机操作工()时,交班主提升机操作工不得擅自离岗。悬吊提升容器
传递动力
悬吊提升容器并传递动力#
牵引设备接班
缺勤#
请假
未到
- 单绳缠绕式提升装置升降人员和物料时安全系数的最低值为()。过卷、松绳等安全保护装置动作不准或不起作用时,()立即进行调整。6.5
7.5
8.5
9.O#不必
应该
必须#
严禁
- 在检查盘式制动闸的碟簧时,各副闸之间,最高开放压力与最低开放压力差不应超过()。缠绕式提升机主要由()等组成。10%#
15%
5%A、工作机构#
B、制动系统#
C、机械传动系统#
D、润滑系统#
E、碱速装置
- 用于轴承润滑的润滑油脂的滴点,一般应高于工作温度()。减速器的安装质量标准有()。10℃~20℃
5℃~10℃
20℃~30℃#
25℃~30℃A、无振动
B、低速轴的直线度误差不大于0.15/1000#
C、不漏油#
D、箱内清洁无杂物#
E、齿
- 一般来说,材料的硬度越高,其()性越好。下列信号必须转发的是()。塑性
韧性
强度
耐磨#A、双罐笼提升信号#
B、箕斗(不包括带乘人间的舞斗)提升信号
C、带乘人的箕斗提升信号#
D、单罐笼提升信号
E、串车提升信
- 斜井用矿车升降物料时,速度不得超过()。9m/s
7m/s
5m/s#
4m/s