查看所有试题
- 交联聚乙烯绝缘电力电缆采用紧压型导体的目的是()。节省导体材料
工艺方便
防止水分进入#
降低电阻率
- 发现巡查的电缆线路有一般缺陷时应()。当电力电缆与通信电缆平行敷设或交叉敷设时可将电缆穿入()。立即报告主管人员;
及时安排消除;
记入缺陷记录薄内;#
填写缺陷通知单。#塑料管材中
玻璃钢管材中
钢制管材
- 一般铝金属的电力设备接头过热后,其颜色会()。在选择钢丝绳安全系数时,应按()原则选用。绝缘体和半导体,导体的区别在于()不同。呈红色;
呈黑色;
呈灰色;#
呈暗红色。重物重量
安全、经济#
经济
安全电阻
导
- YJV型电力电缆型号的含义是()。交联聚乙烯绝缘,聚氯乙烯护套铜电缆。#
交联聚乙烯绝缘,聚乙烯护套铝电缆。
聚氯乙烯绝缘,聚乙烯护套铜电缆。
聚氯乙烯绝缘,聚氯乙烯护套铜电缆。
- 施工作业需占用机动车道时,必须在来车方向前()的机动车道上设置交通警示牌电力电缆的铠装有()种形式电缆固定要求,正确的是()A.10米
B.20米
C.30米
D.50米#A.钢带铠装#
B.铝包铠装
C.铅包铠装
D.钢丝铠
- 电缆按绝缘材料分类有()。兆欧表的用途和测量范围()纸绝缘电缆#
分相铅包电缆
挤包绝缘电缆#
统包绝缘电缆
压力电缆#兆欧表是测量电气设备绝缘电阻的仪表;#
它主要由手摇发电机和测试表头两部分组成;#
常用兆
- 交联聚乙烯铠装电缆最小曲率半径为()电缆外径交联聚乙烯电力电缆有()几种敷设方式。A.10倍
B.15倍#
C.20倍
D.25倍A.直埋敷设#
B.电缆沟内敷设#
C.隧道敷设#
D.排管敷设#
- 感应法电力电缆故障测试仪的用途有()平面锉削一般有()。对110kV交叉互联系统的电缆外护层做绝缘直流耐压试验,试验时()护层保护器断开。寻找电缆路径#
测量电缆埋置深度#
寻找电缆接头位置#
测量闪络故障
测量
- 制作环氧树脂电缆头工作过程中,应采取有效的()措施。交联聚乙烯绝缘电缆附件安装时,以下正确的是()浇灌环氧树脂复合物,夏天比冬天温度()。A.防触电
B.防尘
C.防毒和防火#应严格遵守制作工艺规程;#
冷缩、
- 在超高压电缆接头中,仅能作为塑料电缆接头专用工具是()。A.电缆扳直机
B.绝缘绕包机#
C.压接机
D.真空装置
- 一般10kV以下电缆,将铅包胀到原来铅包直径的()倍。在用绝缘电阻表测试前必须()。油纸电缆一般采用()作耐压试验。1.5
1.2#
1.3
1.1切断被测试设备的电源#
使设备带电测试才准确
与其他仪表配合进行测量
校零B
- 对于10kV直埋电缆穿过农田时,自地面到电缆上面外皮的最小距离为()。0.7m
1.0m#
0.5m
0.9m
- 在高压设备上工作,保证安全的组织措施有()。电缆按绝缘材料分类有()。如图所示电缆敷设常用工具为()。A.工作票制度、工作许可制度
B.工作票制度、工作许可制度、工作监护制度
C.工作票制度、工作许可制度、
- 敷设电缆时,应有专人()。电缆走动时,严禁用手(),以防压伤。红外检测仪器使用现场环境温度一般不宜低于()。环网柜安装前,应检查环网柜柜开关和接地刀闸()位置指示是否正确。A.统一指挥;搬动电缆
B.统一指
- 以下哪些试验项目需要三年进行一次试验。绝缘电阻表简称()。A.充油电缆油样试验#
B.单芯电缆护层电阻测量#
C.红外测温
D.外护套接地电流测试A
- 布置110kV交联聚乙烯电缆线路时,应考虑的因素有()。采用封铅法密封电缆接头时,密封焊条应选用()。电缆工程线路回数。#
每回电缆线路长度,划分段数及各段长度。#
各回路之间的距离,每回路内三根电缆的排列方式和