查看所有试题
- 装车遇有大块岩石掉落铁道中间,影响机车运行,处理大块前应与()取得联系。A、司旗#
B、电车司机
C、调度
- WK-10型电铲的最大挖掘半径为()米。18.6
18.7#
18.8
- 电铲作业场地要保证一定宽度,勺杆应与汽车纵向角度为()。挖掘机运转时规定的信号是,停止运转()A、平行
B、基本成垂直#
C、随意角四短声
三短声#
一短声
- 电铲降段时,主动轴在()。在高段、旧巷、滑落区、火区等危险地点作业时,必须有()。电铲在高段采掘装车时,司机室必须在外侧,汽车应停在外侧,汽车距离坡根距离不得小于段高的()倍。调整挖掘机位置时()必须离开
- 电铲在高段采掘装汽车时,司机室应在()。A、外侧#
B、里侧
C、哪侧都行
- 电铲降段时,主动轴在()。4立方米电铲尾部回转半径是()米。A、前#
B、后
C、前后都可A、3.25
B、4.25
C、5.25#
- 挖掘机横过550伏特以下及电话线,天轮顶端距电线的安全距离是()米4立方米电铲尾部回转半径是()米。调整挖掘机位置时()必须离开地面。0.9
0.7#
0.5A、3.25
B、4.25
C、5.25#勺门
勺斗#
勺杆子
- 电铲降段时,主动轴在()。爬犁车上盘放电缆最小盘放直径不小于()米。A、前#
B、后
C、前后都可A、0.5
B、0.7
C、1#
- 绷绳断丝在每个捻距内不得超过()。WK—4电铲升降坡度为()。电铲附近放炮时,要听从放炮人员指挥,做到把镐()。采掘掌子遇有滑落、片帮危险时应()。高压电缆泡在水里或在火区()。A、7%#
B、8%
C、9%A、1:5#
B
- 调整挖掘机位置时()必须离开地面。苏式4m3电铲回转二轴齿轮的模数是6,齿数是()。WK-10型电铲绷绳长度是()m。勺门
勺斗#
勺杆子100
110#
12050
52.5#
55
- WK-10型电铲的最大挖掘半径为()米。4立方米的最大采掘半径是()米4立方米的最小装车半径为()米。电铲中直流电机整流子面允许最高温度为()度。18.6
18.7#
18.812.5米#
13米
11.5米6米
7.5米#
6.5米90
100#
110
- 挖掘机发生故障时规定信号为()。一短声
一长声
一长一短声#
- 挖掘机开始运转规定信号为()。不按规定持证上岗,给予责任者()。电铲停止作业时,司机室位于()。4立方米的最小装车半径为()米。一长声#
一短声
一长一短A、离岗学习#
B、罚款200元
C、罚款100元A、工作面一侧
- 4m3电铲推压二轴轴泵型号为()。WK—4电铲升降坡度为()。电铲停止作业时,司机室位于()。3624#
3625
3626A、1:5#
B、1:6
C、1:7A、工作面一侧
B、背离工作面一侧#
C、可在随意方向
- 滑动轴承允许的最高温度()度。4立方米的最小装车半径为()米。在掌子行走时,要时刻注意掌子变化,出现滑落、片帮、裂缝等危险迹象时,要立即()。调整挖掘机位置时()必须离开地面。55
60
65#6米
7.5米#
6.5米A、
- WK-10型电铲绷绳长度是()m。爬犁车上盘放电缆最小盘放直径不小于()米。沿坑下公路行走时,要靠公路()边缘行走。调整挖掘机位置时()必须离开地面。50
52.5#
55A、0.5
B、0.7
C、1#A、左侧
B、右侧#
C、任意勺
- 电铲中直流电机整流子面允许最高温度为()度。电铲各部抱闸磨损超过原厚()必须更换。90
100#
11050%
60%#
70%
- 苏式4m3电铲回转二轴齿轮的模数是6,齿数是()。100
110#
120
- 电铲装车时,调整车位信号()。电铲扭车时,每次扭转角度不超过()℃。一短声
二短声
三短声#A、20B、30C、40
- 牙尖的切入深度由()机构通过铲杆的()和()调整的。4m3标准臂电铲在10米段高作业时,所占平盘宽度要大于()米。电铲扶柄大小套注油周期为()。推压;推出;抽回A、12
B、14#
C、16A、每班一次B、每圆班一次C、
- 电铲各部抱闸磨损超过原厚()必须更换。绷绳断丝在每个捻距内不得超过()。50%
60%#
70%A、7%#
B、8%
C、9%
- ()和()在电铲挖掘作业时和岩石直接接触,是极为关键的部件。电铲作业时,回转半径有人,司机应()。滑动轴承允许的最高温度()度。斗前臂;牙尖A、口头制止
B、立即停机#
C、鸣笛警示55
60
65#
- 电铲的冬季操作原则是强调一个()字,突出一个()字。在松软地盘作业的电铲,必须用勺斗压实后再移动,有陷沉危险时必须()。电铲各部抱闸磨损超过原厚()必须更换。稳;慢A、有专人指挥
B、采取有效措施
C、有专人
- 电铲的铲掘方法有三种:()、()和()。不按规定持证上岗,给予责任者()。WK-10型电铲绷绳长度是()m。薄层铲掘;厚层铲掘;非均层铲掘A、离岗学习#
B、罚款200元
C、罚款100元50
52.5#
55
- 可控硅有三个电极:一个是()、一个()和一个()。挖掘机横过550伏特以下及电话线,天轮顶端距电线的安全距离是()米电铲扭车时,每次扭转角度不超过()℃。挖掘机发生故障时规定信号为()。阳;阴;控制极0.9
0.
- 直流电机的常见故障可以分为()故障和()故障两大类。电铲降段时,主动轴在()。绷绳断丝在每个捻距内不得超过()。电铲停止作业时,司机室位于()。用电缆车换电缆时,电铲司机必须在电缆车()米外朝来车方向作
- 直流电动机运行中出现转速异常,表现为()、()、()等。4立方米的最小装车半径为()米。列车进入镐线,车与镐()米时停止回转。苏式4m3电铲回转二轴齿轮的模数是6,齿数是()。转速偏高;转速偏低;转速不稳6米
- 直流发电机实质上是带有()的交流发电机,在()的作用下变交流为直流输出。WK-10型电铲的最大挖掘半径为()米。换向器;换向器18.6
18.7#
18.8
- 为了保证安全,在3WC―0.8/12型压缩机()和()上分别装一、二级安全阀。滑动轴承允许的最高温度()度。冷却器;储气罐55
60
65#
- 行走抱闸的()大小,直接决定着抱合力的大小。苏式4m3电铲回转二轴齿轮的模数是6,齿数是()。间隙100
110#
120
- 润滑可分()润滑、()润滑、()润滑、()润滑等几种。苏式4m3电铲回转二轴齿轮的模数是6,齿数是()。手动干油;稀油飞溅;稀油自动连续;稀油集中100
110#
120
- WK—4电铲升降坡度为()。四立方米电铲的最小采掘半径为()米不能装车的大块岩石应放在()。沿坑下公路行走时,要靠公路()边缘行走。在掌子行走时,要时刻注意掌子变化,出现滑落、片帮、裂缝等危险迹象时,要立即(
- 电铲的转向是由()实现的,()的闭合或开断使左、右两根轴或分离或连接。拨轮;拨轮
- WK―10A铲斗的形式有三种:()()()103;123;143
- 铲斗的运动轨迹是一条复杂的,它决定于()的性质和状态、()铲斗切割边的状态、以及铲斗的()和()速度电铲在高段采掘装车时,司机室必须在外侧,汽车应停在外侧,汽车距离坡根距离不得小于段高的()倍。调整挖掘机
- 储气罐每年进行一次检查,每三年进行一次()检查,每六年至少1次()检查列车进入镐线,车与镐()米时停止回转。外部;内部;全面A、100
B、125
C、150#
- 挖掘机行走装置有三种基本传动形式:()、()、()电铲作业场地要保证一定宽度,勺杆应与汽车纵向角度为()。电铲各部抱闸磨损超过原厚()必须更换。上传动;下传动;端面传动A、平行
B、基本成垂直#
C、随意角5
- 电铲的动力传动机构包括()、()、()、行走及开斗机构。提升;推压;回转
- 曲柄连杆机构采用()、()和()组成。挖掘机行走时,靠线路两侧的履带边缘距线中心不准小于()球墨铸铁悬臂;马口铁连杆;铸铝活塞2米
3米#
4米
- 铲杆的结构有()和()两种。挖掘机运转时规定的信号是,停止运转()双铲杆外插式;单铲杆内插式四短声
三短声#
一短声