查看所有试题
- LCWD-110型电流互感器的第四个字母表示()。充油设备渗漏率按密封点。不能超过()。A、单匹贯穿式
B、单相
C、差动保护#
D、绝缘等级A、0.1%#
B、0.05%
C、0.02%
D、0.01%
- 断路器液压操动机构在()应进行机械闭锁。发生()情况,电压互感器必须立即停止运行。A、压力表指示零压时
B、断路器严重渗油时
C、压力表指示为零且行程杆下降至最下面一个微动开关处时#
D、液压机构打压频繁时A、
- 用兆欧表摇测()时应在摇把转动的情况下。将接线断开。三绕组降压变压器绕组由里向外的排列顺序是()。JDJJ型电压互感器的D表示()。新建、扩建、改建的工程包括继电保护、自动装置、要由运行单位设专人分段验收
- 主变压器重瓦斯动作是由于()造成的。方向继电器采用()接线方式。电流互感器极性对()没有影响。A、主变压器两侧断路器跳闸;
B、220kV套管两相闪络;
C、主变压器内部高压侧绕组严重匝间短路;#
D、主变压器大
- ()接线的电容器组应装设零序平衡保护。距离保护二段的保护范围是()。电压互感器的一、二、三次侧中,()需要接地。A、三角形
B、星形
C、双星形#
D、开口三角形A、不足线路全长
B、线路全长并延伸至下一线路的一
- 单相串级瓷绝缘电压互感器的型号是()。A、JSSW;
B、JDJJ;
C、JDJ;
D、JCC。#
- 变电站的母线上装设避雷器是为了()。变压器的接线组别表示是变压器的高压,低压侧()间的相位关系。一份操作票规定由一组人员操作。()手中只能持一份操作票。A、防止直击雷
B、防止反击过电压
C、防止雷电仃波#
- 仪表的摩擦力矩越大,产生的误差()。双回线路的横差保护的范围是()。220kV电压互感器隔离开关作业时,应拉开二次熔断器是因为()。A、越大#
B、越小
C、不受影响
D、很小A、线路全长#
B、线路的50%
C、相邻线路
- 中性点经消弧绕组接地的电力网,在正常运行情况下中性点,其时间电压位移不应超过额定相电压的()。进行隔离开关操作时,监护人宣读操作项目。操作人复诵,监护人确定无误后发出()执行命令,操作人方可操作。A、5%
B
- 为了保证用户电压质量,系统必须保证有足够的()。过电流方向保护是在过电流保护的基础上。加装一个()而组成的装置。变电所事故处理中应正确迅速在所长领导下执行()命令。A、有功容量
B、电压
C、无功容量#
D、
- 换路定律确定的初始值是由()决定的。防雷保护装置的接地属于()。少油断路器为了防止慢分一般都在断路器()加装防慢分装置。倒闸操作中不得使停电的()由二次返回高压。A、换路前;
B、换路后;
C、换路前瞬间
- 直流控制、信号回路熔断器一般选用()。事故发生后,如需紧急抢修超过()h以上者,应转为事故检修工作。新装电容器的三相电容之间的差值应不超过一相的总电容量的()。用钳型电流表测量电流,测得IA.IB.IC都为10A,如
- 变压器的呼吸器中的硅胶受潮后影变成()。220kV断路器(少油)超行程是()。La5A1002我们把提供电能的装置叫做()A、白色
B、粉红色#
C、蓝色
D、灰色A、75mm
B、55mm
C、70mm#
D、35mm电源#
电动势
发电机
电动
- 变电所事故处理中应正确迅速在所长领导下执行()命令。La5A1004直流电路中,我们把电流流出的一端叫电源的()A、所长
B、值班调度#
C、工区主任
D、生产调度正极#
负极
端电压
电动势
- 大电流接地系统中,任何一点发生单相接地时,零序电流等于通过故障点电流的()。事故发生后,如需紧急抢修超过()h以上者,应转为事故检修工作。A、2倍
B、1.5倍
C、1/3倍#
D、1/5倍A、2
B、3
C、4#
D、5
- 换路定律确定的初始值是由()决定的。定时限过流保护动作值按躲过线路()电流整定。A、换路前;
B、换路后;
C、换路前瞬间;#
D、换路后瞬间。A、最大负荷#
B、平均负荷
C、末端短路
D、出口短路