查看所有试题
- 触电的伤害程度,与()等情况有关。不能用于轻金属燃烧的灭火工作的灭火器材是()。A.通过电流大小B.频率高低C.时间长短D.人体电阻E.通过人体的途径#A.泡沫灭火器B.二氧化碳灭火器C.干粉灭火器D.1211灭火
- 表示推车式灭火器的是()。对VOC的废气处理,目前常用的方法是()。有机溶剂进入人体的途径有()。A.MPB.MPTC.MFBD.MYA.活性炭吸附法B.直接燃烧法C.催化燃烧法D.液体吸附法#吸入
皮肤渗入
A和B选项都可以#
- 对VOC的废气处理,目前常用的方法是()。A.活性炭吸附法B.直接燃烧法C.催化燃烧法D.液体吸附法#
- 引起电气设备绝缘性下降的原因有()。易燃气体的蒸发体积应控制在下限浓度()。A.使用年限增长B.温度升高C.湿度增大D.外壳接地#25%以下#
35%以下
40%以下
- 根据电气设备的绝缘要求,可移动的电气设备的绝缘电阻不能低于()MΩ。防止涂料沉淀的方法,控制储藏室的温度,不能高于()。喷涂双组份丙烯酸聚氨酯时一定要佩戴完善的个人防护用品,正确的选择有()A.0.5
B.1#
C.
- 可防止触电事故的安全措施有()。以下常见的灭火器型号中,属于干粉灭火器的是()。A.电气设备的保护接地B.电气设备的保护接零C.选用安全电压D.提高电气设备的绝缘要求E.电气零线与外壳相连#A.MPTB.MFTC.MF
- 不能用水灭火的是()。A、棉花
B、木材
C、汽油#
- 表示推车式灭火器的是()。表示背负式灭火器的是()。静电设备的高压电缆悬空吊架与电力电缆至少要保持的距离是()。A.MPB.MPTC.MFBD.MYA.MPT
B.MF
C.MTT
D.MFB#20cm
50cm#
35cm
- 使用二氧化碳灭火器时,要注意窒息性气体的浓度,空气中二氧化碳含量达到()会使人呼吸困难。可防止触电事故的安全措施有()。有机溶剂进入人体的途径有()。A.5%B.8.5%C.10%D.15%A.电气设备的保护接地B.
- 有机溶剂乙醇在空气中的最高允许浓度是()。500mg/m3
1500mg/m3#
1000mg/m3
- 喷涂某种涂料时,必须戴供气式口罩,因这种涂料含有()。A.醇酸B.异氰酸酯C.硝基
- 不能用于轻金属燃烧的灭火工作的灭火器材是()。有机溶剂进入人体的途径有()。A.泡沫灭火器B.二氧化碳灭火器C.干粉灭火器D.1211灭火器吸入
皮肤渗入
A和B选项都可以#
- 汽修厂燃油烤房烘烤时,要求易燃气体和溶剂蒸气体积控制在()。触电的伤害程度,与()等情况有关。A.爆炸浓度的25%以下B.爆炸上限浓度的25%以下C.爆炸下限浓度的25%以下A.通过电流大小B.频率高低C.时间长短
- 以下常规的灭火器型号中,属于泡沫灭火器的是()。A.MP#
B.MPT#
C.MF
D.MY
E.MT
F.MFB
G.MTT
- 触电的伤害程度,与()等情况有关。对VOC的废气处理,目前常用的方法是()。有机溶剂进入人体的途径有()。A.通过电流大小B.频率高低C.时间长短D.人体电阻E.通过人体的途径#A.活性炭吸附法B.直接燃烧法C.催
- 进入涂料仓库,()等物品不准带入。目前汽车修理厂可以采用()等方法来减少对环境的污染。对VOC的废气处理,目前常用的方法是()。A.打火机B.香烟C.手机D.BP机E.火柴#A.选用高固体涂料#
B.采用水性涂料#
C.
- 引起电气设备绝缘性下降的原因有()。A.使用年限增长B.温度升高C.湿度增大D.外壳接地#