查看所有试题
- 电力系统电能质量是指:电压、()和波形的质量。当采用380V/220V的TN及TT系统接地形式的低压电网时,照明和其他电力设备宜由()供电,电压偏差的意思是()。电力系统公共连接点由波动负荷产生的闪变限值,与公共连
- 不应小于()。高压水银荧光灯和金属卤化物灯的光通量与电压的关系为()。低压配电系统设计原则不包括()。变配电所直流操作电源中,所谓“端电池”是指()。利用系数法确定用电设备组的计算负荷其公式正确的是()
- 当用电设备距供电点较远,容量小的次要设备,+5%#5,20
5,10#
10,30不应设置开关或熔断器,而应直接连接(不含保护单台电容器的熔断器)#
可以设置自动接通的触点
可以设置断路器
可以设置负荷开关
#
8000kVA
10000kVA
- 正常运行情况下,以下()不属于35kV变电所主变压器的单台(组)容量。三相异步电动机产生最大电磁转矩时对应的转差率称为()。采用人工补偿后,并联电抗器的容量#
变压器容量
改变供配电系统的运行方式#
自动或手动
- 三相平衡线路电压损失计算公式为()。电力系统公共连接点处对于高压HV长时间闪变限值Pit为()。单星形接线的电容器组开口三角电压保护的接线图是()。应急电源EPS的应急供电切换时间为()。10kV开关站的最大转供
- 需要两回路电源线路的用电单位,()采用同级电压供电。但根据各级负荷的不同需要及地区供电条件,亦可采用不同电压供电。同时供电的两回路及以上的供配电线路中,其余线路应能满足全部()供电要求。按《电能质量电压
- 对于第二电源不能满足()的供电要求时,用电单位宜设自备电源。同时供电的两回路及以上的供配电线路中,当一回路中断供电时,其余线路应能满足全部()供电要求。用电单位受电端供电电压偏差允许值,什么情况属于全补偿
- 高压电容器组与放电装置之间()。高压6~35kV配电系统的中性点常用的接地方式没有()。对于6~35kV企业配电系统不采用()。三相平衡线路电压损失计算公式为()。高压单个用户闪变限值的计算公式为()。MV用户第
- 放电器与电容器组的联接方式应为()。线路的送电容量的计算依据不包括()。非线性的用电设备接入电网,会产生谐波电流,应装设()。对冲击性负荷的供电需要降低冲击性负荷引起的电网电压波动和电压闪变(不包括电动
- 对一般照明工作场所,电压偏差允许值宜为()。当没有采取其他防护措施时,车间内吊车裸滑触线距离地面的高度,应不低于()。用于对其电压特性与公用电力系统有相同要求的负载。当负载变化时,可有暂时的电压和频率的偏
- 如果间隔时间小于()算一次变动。抑制谐波的措施不包括()。电压偏差-10%对用电设备全负荷电流的影响有()。关于接在变电所63kV母线上的避雷器和电压互感器下列叙述最恰当的是()。4台用电设备的计算负荷,取设备
- 应急电源与正常电源之间()采取防止并列运行的措施。压电容器组与放电装置之间,可设置()。《电能质量电压波动和闪变》中规定,公共连接点(PCC)是指()。标称电压10kV电缆线路的送电容量为()。电力系统公共连
- 发生单相接地故障时,什么情况属于全补偿?()中性点不接地系统如果为金属性短路时,以下说法正确的是()。当单相接地故障电流()时,应采用下列措施()。必须
应
宜#
不宜四
三
二#
一电感电流等于电容电流#
电感
- 设置自备电源较从电力系统取得()经济合理的用电单位宜设置自备电源。同时供电的两回路及以上的供配电线路中,最大计算负荷时的功率因数应在()。对高层建筑下面说法正确的是()。用于并联电容组的专用放电器选择
- 对应急照明、道路照明和警卫照明电压偏差允许值宜为()。由建筑物外引入的配电线路,应在室内靠近进线点处装设()。中性点不接地系统如果为金属性短路时,仅非故障相对地电压增高而线电压对称性并未遭到破坏,故允许
- 对一般照明工作场所,电压偏差允许值宜为()。在高层建筑物内,当向楼层各配电点供电时,宜采用分区树干式配电;但部分较大容量的集中负荷或重要负荷,()从低压配电室以放射式配电。中性点与地之间接入可调节电感电流
- 电压偏差允许值宜为()。用电单位受电端供电电压的偏差允许值,宜采用三相电网供电。在高层建筑物内,当向楼层各配电点供电时,宜采用分区树干式配电;但部分较大容量的集中负荷或重要负荷,()从低压配电室以放射式配
- 电压偏差允许值宜为()。无功补偿的结果是系统计算电流()。线路的送电容量的计算依据不包括()。电压波动和闪变的产生原因不包括()。电压偏差-10%对用电设备全负荷电流的影响有()。对于用于允许停电时间为毫